HP 2000sa HP StorageWorks 2000 G2 Modular Smart Array reference guide (500911- - Page 103

Examine the FRU specified in the message to, specific event indicating a problem.

Get HP 2000sa PDF manuals and user guides View all HP 2000sa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Table 14 Event code descriptions and recommended actions (continued) Event Event type Description code Recommended action 306 Informational An old serial number in SC flash memory has been updated to a new serial number. 307 Critical A temperature sensor on a controller FRU detected an over-temperature condition that caused the controller to shut down. Check that the storage system's fans are running. Check that the ambient temperature is not too warm. The enclosure operating range is 41-104° F (5-40° C). Check for any obstructions to the airflow. If none of the above explanations apply, replace the controller FRU that reported the error. 308 Informational The default host port speed has changed from 4 Gbit/sec to 2 Gbit/sec because the controller module's HIM has a Broadcom PBC. 309 Informational Normally when the MC is started, the IP data is obtained from the SEEPROM where it is persisted. If the system is unable to write it to the SEEPROM the last time it changed, a flag is set in flash memory. This flag is set during startup, and if set, this event is logged and the IP data that is in flash memory is used. The only time that this would not be the correct IP data would be if the controller board was swapped and then whatever data is on the board's flash memory is used. 310 Informational After a rescan, the controller completed back-end discovery and initialization of enclosure data. 313 Critical An I/O module is down and will not be automatically restarted. This only applies when the other SC goes down. The SC needs service or replacement. 314 Critical A FRU has failed or is not operating correctly. This event follows some other FRU specific event indicating a problem. Examine the FRU specified in the message to determine whether it needs to be replaced. 315 Critical The controller module is incompatible with the enclosure. The controller will automatically shut down. If two incompatible controllers are inserted at the same time, or booted at the same time, one controller will crash and the other will hang. This behavior is expected and prevents data loss. Move the controller module to a compatible controller. 316 Informational The temporary license for a feature is about To continue using the feature after the trial or warning to expire or has expired. This event is logged period, purchase a permanent license. as informational while time remaining in the trial period is nonzero. This event is logged as a warning when the trial period expires. HP StorageWorks 2000 G2 Modular Smart Array Reference Guide 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
HP StorageWorks 2000 G2 Modular Smart Array Reference Guide
103
306
Informational
An old serial number in SC flash memory has
been updated to a new serial number.
307
Critical
A temperature sensor on a controller FRU
detected an over-temperature condition that
caused the controller to shut down.
Check that the storage system’s fans are
running.
Check that the ambient temperature is not
too warm. The enclosure operating range is
41–104
°
F (5–40
°
C).
Check for any obstructions to the airflow.
If none of the above explanations apply,
replace the controller FRU that reported the
error.
308
Informational
The default host port speed has changed
from 4 Gbit/sec to 2 Gbit/sec because the
controller module’s HIM has a Broadcom
PBC.
309
Informational
Normally when the MC is started, the IP data
is obtained from the SEEPROM where it is
persisted. If the system is unable to write it to
the SEEPROM the last time it changed, a flag
is set in flash memory. This flag is set during
startup, and if set, this event is logged and
the IP data that is in flash memory is used.
The only time that this would not be the
correct IP data would be if the controller
board was swapped and then whatever data
is on the board’s flash memory is used.
310
Informational
After a rescan, the controller completed
back-end discovery and initialization of
enclosure data.
313
Critical
An I/O module is down and will not be
automatically restarted. This only applies
when the other SC goes down.
The SC needs service or replacement.
314
Critical
A FRU has failed or is not operating
correctly. This event follows some other FRU
specific event indicating a problem.
Examine the FRU specified in the message to
determine whether it needs to be replaced.
315
Critical
The controller module is incompatible with
the enclosure. The controller will
automatically shut down. If two incompatible
controllers are inserted at the same time, or
booted at the same time, one controller will
crash and the other will hang. This behavior
is expected and prevents data loss.
Move the controller module to a compatible
controller.
316
Informational
or warning
The temporary license for a feature is about
to expire or has expired. This event is logged
as informational while time remaining in the
trial period is nonzero. This event is logged
as a warning when the trial period expires.
To continue using the feature after the trial
period, purchase a permanent license.
Table 14
Event code descriptions and recommended actions (continued)
Event
code
Event type
Description
Recommended action