HP 2000sa HP StorageWorks 2312sa and 2324sa Modular Smart Array user guide (48 - Page 29

If you cannot your access your system for at least three minutes, after changing the, IP address

Get HP 2000sa PDF manuals and user guides View all HP 2000sa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

# set network-parameters ip 192.168.0.11 netmask 255.255.255.0 gateway 193.168.0.10 controller b 7. Type the following command to verify the new IP addresses: show network-parameters Network parameters, including the IP address, subnet mask, and gateway address are displayed for each controller. 8. Use the ping command to verify network connectivity. For example: # ping 192.168.0.10 (gateway) Info: Pinging 192.168.0.10 with 4 packets. Success: Command completed successfully. The remote computer responded with 4 packets. 9. In the host computer's command window, type the following command to verify connectivity, first for controller A and then for controller B: ping controller-IP-address If you cannot your access your system for at least three minutes after changing the IP address, your network might require you to restart the Management Controller(s) using the serial CLI. When you restart a Management Controller, communication with it is temporarily lost until it successfully restarts. Type the following command to restart the management controller on both controllers: restart mc both 10. When you are done using the CLI, exit the emulator. HP StorageWorks 2000sa G2 Modular Smart Array User Guide 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
HP StorageWorks 2000sa G2 Modular Smart Array User Guide
29
# set network-parameters ip 192.168.0.11 netmask 255.255.255.0 gateway
193.168.0.10 controller b
7.
Type the following command to verify the new IP addresses:
show network-parameters
Network parameters, including the IP address, subnet mask, and gateway address are displayed for
each controller.
8.
Use the
ping
command to verify network connectivity.
For example:
# ping 192.168.0.10 (gateway)
Info: Pinging 192.168.0.10 with 4 packets.
Success: Command completed successfully. The remote computer responded
with 4 packets.
9.
In the host computer's command window, type the following command to verify connectivity, first for
controller A and then for controller B:
ping controller-
IP-address
If you cannot your access your system for at least three minutes
after changing the
IP address
, your network might require you to restart the Management Controller(s) using the serial
CLI. When you restart a Management Controller, communication with it is temporarily lost until it
successfully restarts.
Type the following command to restart the management controller on both controllers:
restart mc both
10.
When you are done using the CLI, exit the emulator.