HP 6400/8400 HP StorageWorks Enterprise Virtual Array updating product softwar - Page 60

I/O tab of Disk Enclosure Properties window, The Disk Enclosure Properties window opens.

Get HP 6400/8400 PDF manuals and user guides View all HP 6400/8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

1. In HP Command View EVA, go to the Hardware folder in the Navigation pane and select a disk enclosure. The Disk Enclosure Properties window opens. 2. Select the I/O tab. 3. Verify that 0073 displays in the Firmware revision field (for both I/O module A and B). See Figure 19. If so, the upgrade was successful. If not, resetting the I/O module is recommended. Figure 19 I/O tab of Disk Enclosure Properties window . In a few cases, it has been observed that some fields on the I/O tab of the Disk Enclosure Properties window appear blank, specifically Hardware revision, Hardware type, and Assembly serial number (see Figure 20). These blank fields do not affect I/O module operation and do not indicate that the upgrade was unsuccessful. HP recommends that you wait 20 minutes to see if the situation corrects itself. If not, you can reset the I/O module to populate these fields (optional). 60 Upgrading the Enterprise Virtual Array

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
1.
In HP Command View EVA, go to the Hardware folder in the Navigation pane and select a disk
enclosure.
The Disk Enclosure Properties window opens.
2.
Select the
I/O
tab.
3.
Verify that 0073 displays in the Firmware revision field (for both I/O module A and B). See
Figure 19
. If so, the upgrade was successful. If not, resetting the I/O module is recommended.
Figure 19 I/O tab of Disk Enclosure Properties window
.
In a few cases, it has been observed that some fields on the I/O tab of the Disk Enclosure Properties
window appear blank, specifically Hardware revision, Hardware type, and Assembly serial number
(see
Figure 20
). These blank fields do not affect I/O module operation and do not indicate that the
upgrade was unsuccessful. HP recommends that you wait 20 minutes to see if the situation corrects
itself. If not, you can reset the I/O module to populate these fields (optional).
Upgrading the Enterprise Virtual Array
60