HP 6400/8400 HP StorageWorks EVA6400/8400 M6412A disk enclosure installation i - Page 13

number of the next higher enclosure number. For example, if the previous highest index number, was 3

Get HP 6400/8400 PDF manuals and user guides View all HP 6400/8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

9. Power on controller A by pressing the power button on rear of the controller until the controller responds (it may take up to 10 seconds for the controller to power on). Repeat this step for controller B. Wait five minutes for the array to stabilize. 10. Verify that I/O modules A and B on the added disk enclosure have been assigned an index number of the next higher enclosure number. For example, if the previous highest index number was "3," then the installed enclosure should display "4." 11. In HP P6000 Command View, verify that the newly installed disk enclosure appears as part of the array hardware in the navigation pane, and that the I/O modules show a good operational status. Figure 17 Revised cabling when one disk enclosure is added to loop 1 (EVA8400) Loop 1 I/O-A P1 / P2 I/O-B P1 / P2 01 I/O-A P1 / P2 I/O-B P1 / P2 Shelf-4 (S-4) 04 Shelf-3 (S-3) 03 02 Memory Card DP1-AMf/g DP2-A / DP3-A DP1-A DP2-A DP3-A MP1 FP1 FP2 FP3 FP4 01 MP1 - MP2 - Jumper Cables Memory Card DP1-AMfg/ DP2-A / DP3-A DP1-A DP2-A DP3-A MP1 FP1 FP2 FP3 FP4 02 Controller "A" UID DP1-B / DP2-B / DP3-B MP2 DP1-B DP2-B DP3-B PS 1 03 Controller "B" UID DP1-B / DP2-B / DP3-B MP2 DP1-B DP2-B DP3-B PS 1 PS 2 PS 2 04 Cabling the enclosure 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
9.
Power on controller A by pressing the power button on rear of the controller until the controller
responds (it may take up to 10 seconds for the controller to power on). Repeat this step for
controller B. Wait five minutes for the array to stabilize.
10. Verify that I/O modules A and B on the added disk enclosure have been assigned an index
number of the next higher enclosure number. For example, if the previous highest index number
was “3,” then the installed enclosure should display “4.”
11.
In HP P6000 Command View, verify that the newly installed disk enclosure appears as part of
the array hardware in the navigation pane, and that the I/O modules show a good operational
status.
Figure 17 Revised cabling when one disk enclosure is added to loop 1 (EVA8400)
Memory Card
UID
Mfg
DP1-A
DP2-A
DP3-A
MP1
FP1
FP2
FP3
FP4
MP2
DP1-B
DP2-B
DP3-B
Memory Card
UID
Mfg
DP1-A
DP2-A
DP3-A
MP1
FP1
FP2
FP3
FP4
MP2
DP1-B
DP2-B
DP3-B
Controller “A”
Controller “B”
MP1 – MP2 –
Jumper Cables
DP1-A / DP2-A / DP3-A
DP1-B / DP2-B / DP3-B
DP1-B / DP2-B / DP3-B
Shelf-3 (S-3)
DP1-A / DP2-A / DP3-A
02
02
03
03
Shelf-4 (S-4)
P1 / P2
P1 / P2
I/O-A
I/O-B
Loop 1
01
01
04
04
P1 / P2
P1 / P2
I/O-A
I/O-B
Cabling the enclosure
13