HP AD510A HP StorageWorks 1500 Modular Smart Array Installation Guide (355901- - Page 43

Step 5: Install the hard drives, Table 13, Hard Drive Information

Get HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive PDF manuals and user guides
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Installation Procedures - All Deployments Step 5: Install the hard drives After the storage enclosures are secured in the rack, install the hard drives into the drive bays. For a list of supported hard drives, see the compatibility guide, located on the Technical documents page of the MSA1500 website: http://www.hp.com/go/msa1500cs. Caution: Follow industry-standard practices when handling hard drives. Internal storage media can be damaged when drives are shaken, dropped, or roughly placed on a work surface. When installing a hard drive, make sure it is fully seated in the drive bay. To remove a hard drive, press the release button and pull the drive only slightly out of the enclosure.Then, to allow time for the internal disk to stop rotating, wait approximately 10 seconds before completely removing the drive from the enclosure. Note: HP recommends installing hard drives in bay-number sequence. Locate this information for your storage enclosure in the enclosure documentation. For information about installing hard drives, refer to the instructions that came with the hard drive and the enclosure. Go to Table 13: "Hard Drive Information" on page 114 to record information about your hard drives. HP StorageWorks 1500 Modular Smart Array Installation Guide 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Installation Procedures - All Deployments
43
HP StorageWorks 1500 Modular Smart Array Installation Guide
Step 5: Install the hard drives
After the storage enclosures are secured in the rack, install the hard drives into the
drive bays. For a list of supported hard drives, see the compatibility guide, located
on the Technical documents page of the MSA1500 website:
.
Caution:
Follow industry-standard practices when handling hard drives.
Internal storage media can be damaged when drives are shaken, dropped, or
roughly placed on a work surface. When installing a hard drive, make sure it
is fully seated in the drive bay. To remove a hard drive, press the release button
and pull the drive only slightly out of the enclosure.Then, to allow time for the
internal disk to stop rotating, wait approximately 10 seconds before completely
removing the drive from the enclosure.
Note:
HP recommends installing hard drives in bay-number sequence. Locate this
information for your storage enclosure in the enclosure documentation.
For information about installing hard drives, refer to the instructions that came
with the hard drive and the enclosure.
Go to
Table 13
: “
Hard Drive Information
” on page 114 to record information
about your hard drives.