HP AD510A HP StorageWorks 1500 Modular Smart Array Installation Guide (355901- - Page 59

Table 10, MSA1500 Information, Go to, on to record the controller, firmware version.

Get HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive PDF manuals and user guides
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Installation Procedures - All Deployments Read the messages on the controller display panel Each controller contains an integrated LCD panel. This panel displays informational and error messages, shows the current status of the MSA, and provides an interface for user input. To verify that your MSA is operating properly, use the arrow buttons on the LCD panel of the controller and look for the following messages: Table 8: MSA1500 Startup Messages Message Startup Complete Fibre Sub-System Link Failure Array controller Firmware ver Meaning The array controller has completed its power on sequence and is operational. No active fiber connection to the MSA controller exists. This message is expected, because, although you have physically installed the HBA in the server, you have not yet installed the drivers for the HBA and the MSA. You may safely ignore this message. The current version of the firmware running on the controller. If the Startup Complete message is not displayed: ■ Check the cable connections to the MSA ■ Check the availability of your power source ■ Review the setup instructions in the previous sections of this guide ■ Refer to the HP StorageWorks MSA1500 Maintenance and Service Guide, available on the Documentation CD and the Technical documents page of the MSA1500 website: http://www.hp.com/go/msa1500cs. Go to Table 10: "MSA1500 Information" on page 108 to record the controller firmware version. HP StorageWorks 1500 Modular Smart Array Installation Guide 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Installation Procedures - All Deployments
59
HP StorageWorks 1500 Modular Smart Array Installation Guide
Read the messages on the controller display panel
Each controller contains an integrated LCD panel. This panel displays
informational and error messages, shows the current status of the MSA, and
provides an interface for user input. To verify that your MSA is operating
properly, use the arrow buttons on the LCD panel of the controller and look for the
following messages:
If the
Startup Complete
message is not displayed:
■
Check the cable connections to the MSA
■
Check the availability of your power source
■
Review the setup instructions in the previous sections of this guide
■
Refer to the
HP StorageWorks
MSA1500 Maintenance and Service Guide
,
available on the Documentation CD and the Technical documents page of the
MSA1500 website:
.
Go to
Table 10
: “
MSA1500 Information
” on page 108 to record the controller
firmware version.
Table 8:
MSA1500 Startup Messages
Message
Meaning
Startup Complete
The array controller has completed its
power on sequence and is operational.
Fibre Sub-System Link Failure
No active fiber connection to the MSA
controller exists. This message is
expected, because, although you have
physically installed the HBA in the
server, you have not yet installed the
drivers for the HBA and the MSA.
You may safely ignore this message.
Array controller Firmware ver
<version>
The current version of the firmware
running on the controller.