HP AD510A HP StorageWorks 1500 Modular Smart Array Installation Guide (355901- - Page 95

Tru64 UNIX environments, The AlphaServer must have Tru64 UNIX v5.1.b PK4 or later installed.

Page 95 highlights

Configuration Procedures - Other Environments d. For each HBA, verify that the following options are specified: load ql2x00.ham slot=x/luns/allpaths/portnames, where x represents the slot number. Note: The Native MPIO solution can co-exist with HP Secure Path for NetWare. ■ If the MSA is upgraded to 6.86or later active/active firmware, and, if you want to remove the Secure Path for NetWare driver, do the following: a. Follow the removal instructions provided in the Secure Path user documents. b. From the console, enter edit c:\NWSERVER\STARTUP.NCF. c. Comment out the following entry: #load hpqsp.cdm d. Enter edit sys:\system\autoexec.ncf e. Comment out the following entries: LOAD hpqspagt.nlm LOAD hpqspahw.nlm Tru64 UNIX environments ■ Single-controller configurations and active/passive firmware are not supported; the MSA must be upgraded to dual-controllers running active/active firmware. ■ The AlphaServer must have Tru64 UNIX v5.1.b PK4 (or later) installed. ■ The AlphaServer must be configured in a SAN switch zone with the MSA. ■ After installing the MSA, be sure to set the host mode for each Tru64 UNIX connection to tru64. ■ For information on upgrading the MSA to active/active, see the migration instructions for Tru64 UNIX environments, available on the Technical documents page of the MSA1500 website: http://www.hp.com/go/msa1500cs. HP StorageWorks 1500 Modular Smart Array Installation Guide 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126

Configuration Procedures - Other Environments
95
HP StorageWorks 1500 Modular Smart Array Installation Guide
d.
For each HBA, verify that the following options are specified:
load
ql2x00.ham slot=x/luns/allpaths/portnames
, where x
represents the slot number.
Note:
The Native MPIO solution can co-exist with HP Secure Path for NetWare.
If the MSA is upgraded to 6.86or later active/active firmware, and, if you want
to remove the Secure Path for NetWare driver, do the following:
a.
Follow the removal instructions provided in the Secure Path user
documents.
b.
From the console, enter
edit c:\NWSERVER\STARTUP.NCF
.
c.
Comment out the following entry:
#load hpqsp.cdm
d.
Enter
edit sys:\system\autoexec.ncf
e.
Comment out the following entries:
Tru64 UNIX environments
Single-controller configurations and active/passive firmware are not
supported; the MSA must be upgraded to dual-controllers running
active/active firmware.
The AlphaServer must have Tru64 UNIX v5.1.b PK4 (or later) installed.
The AlphaServer must be configured in a SAN switch zone with the MSA.
After installing the MSA, be sure to set the host mode for each Tru64 UNIX
connection to
tru64
.
For information on upgrading the MSA to active/active, see the migration
instructions for Tru64 UNIX environments, available on the Technical
documents page of the MSA1500 website:
.
LOAD hpqspagt.nlm
LOAD hpqspahw.nlm