HP AD510A HP StorageWorks 1500 Modular Smart Array Installation Guide (355901- - Page 94

Operating-system-specific notes, NetWare environments

Get HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive PDF manuals and user guides
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Configuration Procedures - Other Environments Operating-system-specific notes Note: SCO UNIX, VMWare, OpenVMS, and Tru64 UNIX do not use the provided MSA Support Software CD. These operating systems use the MSA-CLI to configure the storage and obtain the HBA drivers and multipathing tools from a different source, such as through operating system updates or the HP website. NetWare environments ■ Single-controller configurations are supported for use with active/passive firmware only. Dual-controller configurations are supported for use with either active/passive (using Secure Path as the multipathing software) or active/active firmware (using the native NetWare MPIO multipathing software). ■ For information on upgrading the MSA to active/active, see the migration instructions for NetWare environments, available on the Technical documents page of the MSA1500 website: http://www.hp.com/go/msa1500cs. ■ If desired, NetWare environments can use the Array Configuration Utility to configure the MSA. The ACU is provided on the MSA Support Software CD and can be installed and run from a Windows or Linux server, or, the NetWare server can boot to the CD and run the ACU offline from the CD. ■ If using the ACU to configure the MSA, install Netscape Navigator version 6.2 or later or Mozilla, version 1.0.2 or later with Personal Security Manager. ■ After installing the MSA, be sure to set the host mode for each NetWare connection to netware. ■ If the MSA is upgraded to 6.86 or later active/active firmware, do the following to activate the native MPIO provided by Novell. From the console: a. Enter edit c:\nwserver\startup.ncf. b. Add the following entry as the first line in the startup.ncf file: set multi-path support = on c. Locate the following entry and modify it: Old entry LOAD SCSIHD.CDM Modified entry LOAD SCSIHD.CDM /AEN 94 HP StorageWorks 1500 Modular Smart Array Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Configuration Procedures - Other Environments
94
HP StorageWorks 1500 Modular Smart Array Installation Guide
Operating-system-specific notes
Note:
SCO UNIX, VMWare, OpenVMS, and Tru64 UNIX do not use the provided
MSA Support Software CD. These operating systems use the MSA-CLI to configure the
storage and obtain the HBA drivers and multipathing tools from a different source, such
as through operating system updates or the HP website.
NetWare environments
■
Single-controller configurations are supported for use with active/passive
firmware only. Dual-controller configurations are supported for use with
either active/passive (using Secure Path as the multipathing software) or
active/active firmware (using the native NetWare MPIO multipathing
software).
■
For information on upgrading the MSA to active/active, see the migration
instructions for NetWare environments, available on the Technical documents
page of the MSA1500 website:
.
■
If desired, NetWare environments can use the Array Configuration Utility to
configure the MSA. The ACU is provided on the MSA Support Software CD
and can be installed and run from a Windows or Linux server, or, the NetWare
server can boot to the CD and run the ACU offline from the CD.
■
If using the ACU to configure the MSA, install Netscape Navigator version
6.2 or later or Mozilla, version 1.0.2 or later with Personal Security Manager.
■
After installing the MSA, be sure to set the host mode for each NetWare
connection to
netware
.
■
If the MSA is upgraded to 6.86 or later active/active firmware, do the
following to activate the native MPIO provided by Novell.
From the console:
a.
Enter
edit c:\nwserver\startup.ncf
.
b.
Add the following entry as the first line in the startup.ncf file:
set multi-path support = on
c.
Locate the following entry and modify it:
Old entry
Modified entry
LOAD SCSIHD.CDM
LOAD SCSIHD.CDM /AEN