HP Cisco MDS 9020 Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Rele - Page 33

Downgrading the SSI Image on Your SSM

Get HP Cisco MDS 9020 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Downgrading Your Cisco MDS SAN-OS Software Image Send documentation comments to [email protected] Although the switch indicates that the bootflash check takes 30 minutes, it typically completes in just a few seconds. Once the bootflash check is complete on both the active and the standby supervisors, proceed with the downgrade process. Note The system health check bootflash command is available starting in NX-OS 4.1(1b). Downgrading the SSI Image on Your SSM Use the following guidelines when downgrading your SSI image on your SSM: • On a system with at least one SSM installed, the install all command might fail on an SSM when you downgrade from Cisco NX-OS Release 4.1 to any SAN-OS 2.x release earlier than SAN-OS Release 2.1(2e). Power down the SSM and perform the downgrade. Bring up the SSM with the new bootvar set to the 2.x SSI image. • Downgrade the SSI boot images on the SSMs on the switch to a release version supported by your Cisco SAN-OS release. Refer to the Cisco MDS SAN-OS Release Compatibility Matrix for Storage Service Interface Images. • SSM intelligent services traffic switching on SSM ports is disrupted on upgrades or downgrades. • Fibre Channel switching traffic on SSM ports is not disrupted under the following conditions: - All SSM applications are disabled. Use the show ssm provisioning command to determine if any applications are provisioned on the SSM. Use the no ssm enable feature configuration mode command to disable these features. - The EPLD version on the SSM is at 0x07 or higher. Use the show version module slot epld command to determine your EPLD version. Refer to the Cisco MDS 9000 Family Release Notes for Cisco MDS 9000 EPLD Images to upgrade your EPLD image. - Refer to the Cisco MDS 9000 Family Interoperability Support Matrix and the "Managing Modules" chapter in the Cisco MDS 9000 Family CLI Configuration Guide, Release 3.x, for information on downgrading your SSM. OL-17675-02 Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 4.1(1b) 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Send documentation comments to [email protected]
33
Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 4.1(1b)
OL-17675-02
Downgrading Your Cisco MDS SAN-OS Software Image
Although the switch indicates that the bootflash check takes 30 minutes, it typically completes in
just a few seconds.
Once the bootflash check is complete on both the active and the standby supervisors, proceed with
the downgrade process.
Note
The s
ystem health check bootflash
command is available starting in NX-OS 4.1(1b).
Downgrading the SSI Image on Your SSM
Use the following guidelines when downgrading your SSI image on your SSM:
•
On a system with at least one SSM installed, the
install all
command might fail on an SSM when
you downgrade from Cisco NX-OS Release 4.1 to any SAN-OS 2.x release earlier than SAN-OS
Release 2.1(2e). Power down the SSM and perform the downgrade. Bring up the SSM with the new
bootvar set to the 2.x SSI image.
•
Downgrade the SSI boot images on the SSMs on the switch to a release version supported by your
Cisco SAN-OS release. Refer to the
Cisco MDS SAN-OS Release Compatibility Matrix for Storage
Service Interface Images
.
•
SSM intelligent services traffic switching on SSM ports is disrupted on upgrades or downgrades.
•
Fibre Channel switching traffic on SSM ports
is not disrupted under the following conditions:
–
All SSM applications are disabled. Use the
show ssm provisioning
command to determine if
any applications are provisioned on the SSM. Use the
no ssm enable feature
configuration
mode command to disable these features.
–
The EPLD version on the SSM is at 0x07 or higher. Use the
show version module
slot
epld
command to determine your EPLD version. Refer to the
Cisco MDS 9000 Family Release Notes
for Cisco MDS 9000 EPLD Images
to upgrade your EPLD image.
–
Refer to the
Cisco MDS 9000 Family Interoperability Support Matrix
and the “Managing
Modules” chapter in the
Cisco MDS 9000 Family CLI Configuration Guide, Release 3.x
,
for
information on downgrading your SSM.