HP Cisco MDS 9020 Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Rele - Page 54

x45F0 corresponds to HPUX's Volume Set Address <VBUS ID: 0xB, Target ID: 0xE, LUN: 0x0>.

Page 54 highlights

Caveats Send documentation comments to [email protected] • CSCso63465 Symptom: FCP-CMD (for example, Inquiry) frames targeted to LUN 0x45F0 or LUN 0x50F0 are dropped by an MDS switch when traffic flows (egresses) through Generation 2 modules. LUN 0x45F0 corresponds to HPUX's Volume Set Address . Workaround: This issue is resolved. • CSCso66705 Symptom: The FCNS process may fail and dump a core. The process is then gracefully restarted by the system. Because this condition takes a relatively long time to develop, it is unlikely that the FCNS process will fail frequently enough to cause the active supervisor to reboot. Workaround: This issue is resolved. • CSCso87408 Symptom: A scheduled web report fails to generate when the fabric is deleted from Fabric Manager. The log records "Fabric not found fabricID=xxx". Workaround: This issue is resolved. • CSCsq54455 Symptom: On a DS-X9032 module where the SRAM parity error was seen, the SRAM parity error exceptions were logged continuously. Workaround: This issue is resolved. • CSCsq57352 Symptom: After upgrading from Fabric Manager Release 3.0(2a) to Fabric Manager Release 3.2(3a), the Fabric Manager client fails to reuse the map layout files produced by Release 3.0(2a). Renaming the map layout files will make them compatible with Fabric Manager Release 3.2(3a). Workaround: This issue is resolved. • CSCsq60582 Symptom: Multiple Cisco products contain either of two authentication vulnerabilities in the Simple Network Management Protocol Version 3 (SNMPv3) feature. These vulnerabilities can be exploited when processing a malformed SNMPv3 message. These vulnerabilities could allow the disclosure of network information or may enable an attacker to perform configuration changes to vulnerable devices. The SNMP server is an optional service that is disabled by default. Only SNMPv3 is impacted by these vulnerabilities. Note SNMP versions 1, 2 and 2c are not impacted by these vulnerabilities. The United States Computer Emergency Response Team (US-CERT) has assigned Vulnerability Note VU#878044 to these vulnerabilities. Common Vulnerabilities and Exposures (CVE) identifier CVE-2008-0960 has been assigned to these vulnerabilities. This advisory is posted at http://www.cisco.com/en/US/products/products_security_advisory09186a00809ac83b.shtml. Workarounds are available for mitigating the impact of the vulnerabilities described in this document. Workaround: This issue is resolved. Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 4.1(1b) 54 OL-17675-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66

Send documentation comments to [email protected]
54
Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 4.1(1b)
OL-17675-02
Caveats
CSCso63465
Symptom
: FCP-CMD (for example, Inquiry) frames targeted to LUN 0x45F0 or LUN 0x50F0 are
dropped by an MDS switch when traffic flows (egresses) through Generation 2 modules. LUN
0x45F0 corresponds to HPUX's Volume Set Address <VBUS ID: 0xB, Target ID: 0xE, LUN: 0x0>.
Workaround
: This issue is resolved.
CSCso66705
Symptom
: The FCNS process may fail and dump a core. The process is then gracefully restarted by the
system. Because this condition takes a relatively long time to develop, it is unlikely that the FCNS process
will fail frequently enough to cause the active supervisor to reboot.
Workaround
: This issue is resolved.
CSCso87408
Symptom
: A scheduled web report fails to generate when the fabric is deleted from Fabric Manager.
The log records “Fabric not found fabricID=xxx”.
Workaround
: This issue is resolved.
CSCsq54455
Symptom
: On a DS-X9032 module where the SRAM parity error was seen, the SRAM parity error
exceptions were logged continuously.
Workaround
: This issue is resolved.
CSCsq57352
Symptom
: After upgrading from Fabric Manager Release 3.0(2a) to Fabric Manager
Release 3.2(3a), the Fabric Manager client fails to reuse the map layout files produced by Release
3.0(2a). Renaming the map layout files will make them compatible with Fabric Manager Release
3.2(3a).
Workaround
: This issue is resolved.
CSCsq60582
Symptom
: Multiple Cisco products contain either of two authentication vulnerabilities in the
Simple Network Management Protocol Version 3 (SNMPv3) feature. These vulnerabilities can be
exploited when processing a malformed SNMPv3 message. These vulnerabilities could allow the
disclosure of network information or may enable an attacker to perform configuration changes to
vulnerable devices. The SNMP server is an optional service that is disabled by default. Only
SNMPv3 is impacted by these vulnerabilities.
Note
SNMP versions 1, 2 and 2c are not impacted by these vulnerabilities.
The United States Computer Emergency Response Team (US-CERT) has assigned Vulnerability
Note VU#878044 to these vulnerabilities. Common Vulnerabilities and Exposures (CVE) identifier
CVE-2008-0960 has been assigned to these vulnerabilities.
This advisory is posted at
.
Workarounds are available for mitigating the impact of the vulnerabilities described in this
document.
Workaround
: This issue is resolved.