HP Cisco Nexus 5000 Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Re - Page 44

Applying Zone Configurations to VSAN 1, Running Storage Applications on the MSM-18/4, VF_ID Value

Get HP Cisco Nexus 5000 - Converged Network Switches PDF manuals and user guides View all HP Cisco Nexus 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Limitations and Restrictions Send documentation comments to mdsfeedback-doc.com. • If trunk mode is on for any of the interfaces or NP PortChannel is up, the reserved VSANs are 3040 to 4078, and they are not available for user configuration. • The Exchange Virtual Fabric Protocol (EVFP) isolated VSAN is 4079, and it is not available for user configuration. • VSAN 4079 will be impacted by an upgrade to NX-OS Release 4.1(3a), depending on whether or not VSAN 4079 was created prior to the upgrade. See the "Upgrading Effect on VSAN 4079" section on page 20 for details. The following VSAN IDs are assigned in the Fibre Channel Framing and Signaling (FC-FS) interface standard: VF_ID Value 00h 001h ... EFFh F00h ... FEEh FEFh FF0h ... FFEh FFFh FEFh = 4079 Value Description Do not use as a Virtual Fabric Identifier. Available as a Virtual Fabric Identifier. Reserved. Control VF-ID (see Fibre Channel Link Services (FC-LS) and Fibre Channel Switch Fabric Generation 4 (FC-SW-4) standards). Vendor specific. Do not use as a Virtual Fabric Identifier. Applying Zone Configurations to VSAN 1 In the setup script, you can configure system default values for the default-zone to be permit or deny, and you can configure default values for the zone distribution method and for the zone mode. These default settings are applied when a new VSAN is created. However, the settings will not take effect on VSAN 1, because it exists prior to running the setup script. Therefore, when you need those settings for VSAN 1, you must explicitly issue the following commands: • zone default-zone permit vsan 1 • zoneset distribute full vsan 1 • zone mode enhanced vsan 1 Running Storage Applications on the MSM-18/4 The Cisco MDS 9000 18/4-Port Multiservice Module (MSM-18/4) does not support multiple, concurrent storage applications. Only one application, such as SME or DMM, can run on the MSM-18/4 at a time. Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 4.1(3a) 44 OL-17675-05

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Send documentation comments to mdsfeedback-doc.com.
44
Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 4.1(3a)
OL-17675-05
Limitations and Restrictions
•
If trunk mode is on for any of the interfaces or NP PortChannel is up, the reserved VSANs are 3040
to 4078, and they are not available for user configuration.
•
The Exchange Virtual Fabric Protocol (EVFP) isolated VSAN is 4079, and it is not available for user
configuration.
•
VSAN 4079 will be impacted by an upgrade to NX-OS Release 4.1(3a), depending on whether or
not VSAN 4079 was created prior to the upgrade. See the
“Upgrading Effect on VSAN 4079”
section on page 20
for details.
The following VSAN IDs are assigned in the Fibre Channel Framing and Signaling (FC-FS) interface
standard:
Applying Zone Configurations to VSAN 1
In the setup script, you can configure system default values for the default-zone to be permit or deny,
and you can configure default values for the zone distribution method and for the zone mode.
These default settings are applied when a new VSAN is created. However, the settings will not take effect
on VSAN 1, because it exists prior to running the setup script. Therefore, when you need those settings
for VSAN 1, you must explicitly issue the following commands:
•
zone default-zone permit
vsan 1
•
zoneset distribute full
vsan 1
•
zone mode enhanced
vsan 1
Running Storage Applications on the MSM-18/4
The Cisco MDS 9000 18/4-Port Multiservice Module (MSM-18/4) does not support multiple, concurrent
storage applications. Only one application, such as SME or DMM, can run on the MSM-18/4 at a time.
VF_ID Value
Value Description
00h
Do not use as a Virtual Fabric Identifier.
001h ... EFFh
Available as a Virtual Fabric Identifier.
F00h ... FEEh
Reserved.
FEFh
Control VF-ID (see Fibre Channel Link Services
(FC-LS) and Fibre Channel Switch Fabric
Generation 4 (FC-SW-4) standards).
FF0h ... FFEh
Vendor specific.
FFFh
Do not use as a Virtual Fabric Identifier.
FEFh = 4079