HP Integrity Superdome 2 8/16 HP Integrity Superdome 2 Onboard Administrator U - Page 41

First Time Setup Wizard, Before you begin, Enclosure Selection screen

Get HP Integrity Superdome 2 8/16 PDF manuals and user guides View all HP Integrity Superdome 2 8/16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

4 First Time Setup Wizard NOTE: The First Time Setup Wizard is used only to configure compute enclosures and Onboard Administrator network settings. The First Time Setup Wizard does not enable you to set up and configure partitions. For information on partition creation and management, see the HP Integrity Superdome 2 Partitioning Administrator Guide. Before you begin Before running the First Time Setup Wizard, complete the following tasks: 1. Install the Onboard Administrator modules. 2. Connect the Onboard Administrator modules to the network. 3. Complete the Insight Display installation wizard. You must at least configure the active Onboard Administrator IP address. 4. Run the Insight Display installation. Logging on to Onboard Administrator For information on logging on to the Onboard Administrator, see "Logging on to the Onboard Administrator GUI" (page 15). The first time you log on, the Onboard Administrator automatically runs the First Time Setup Wizard. To navigate the setup wizard, click the Next button to save your changes and go to the next step. Click the Skip button if you want to leave the step without saving the changes. You can return to previous wizard steps by selecting them in the left tree view. You can also run the wizard again at any time by selecting it from the Wizards menu. Enclosure Selection screen The Enclosure Selection screen displays all discovered enclosures and selects the active enclosure, the enclosure you are signed in to by default. The check box beside each enclosure enables you to select or clear that enclosure. Selecting the check box beside All Enclosures toggles the check box for all enclosures. Click the Refresh Topology button to update the rack topology information. When you select Refresh Topology, the Enclosure Selection screen switches to the Linked Mode and all linked enclosures appear. Before you begin 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
4 First Time Setup Wizard
NOTE:
The First Time Setup Wizard is used only to configure compute enclosures and Onboard
Administrator network settings. The First Time Setup Wizard does not enable you to set up and
configure partitions.
For information on partition creation and management, see the
HP Integrity Superdome 2 Partitioning
Administrator Guide
.
Before you begin
Before running the First Time Setup Wizard, complete the following tasks:
1.
Install the Onboard Administrator modules.
2.
Connect the Onboard Administrator modules to the network.
3.
Complete the Insight Display installation wizard. You must
at least
configure the active Onboard
Administrator IP address.
4.
Run the Insight Display installation.
Logging on to Onboard Administrator
For information on logging on to the Onboard Administrator, see
“Logging on to the Onboard
Administrator GUI” (page 15)
.
The first time you log on, the Onboard Administrator automatically runs the First Time Setup Wizard.
To navigate the setup wizard, click the
Next
button to save your changes and go to the next step.
Click the
Skip
button if you want to leave the step without saving the changes.
You can return to previous wizard steps by selecting them in the left tree view. You can also run
the wizard again at any time by selecting it from the
Wizards
menu.
Enclosure Selection screen
The Enclosure Selection screen displays all discovered enclosures and selects the active enclosure,
the enclosure you are signed in to by default. The check box beside each enclosure enables you
to select or clear that enclosure. Selecting the check box beside All Enclosures toggles the check
box for all enclosures.
Click the
Refresh Topology
button to update the rack topology information. When you select
Refresh
Topology
, the Enclosure Selection screen switches to the Linked Mode and all linked enclosures
appear.
Before you begin
41