Home » HP Manuals » Bridges & Routers » HP J4819A » Manual Viewer

HP J4819A User Manual - Page 30

(Optional) Install Second Power Supply, Caution

Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Installing the Switch 5300xl Series Installing the Switch 5300xl Series Installation Procedures 3. (Optional) Install Second Power Supply A second, load-sharing redundant power supply (ProCurve Switch gl/xl/vl RPS, J4839A) can be installed in the back of the switch. To provide true redundancy, this second power supply should be connected to a different AC power source from the other supply. Then, if one AC power source fails, the switch will continue to run. Each supply provides enough power to operate a fully loaded switch, so even if one fails, the switch will continue to operate normally. Install the second power supply into power slot number 2 as shown in the illustration on the next page. The slot cover can be removed with either a flat-bladed or Torx T-10 screwdriver. Retain the slot cover for future use. Caution The switch power supplies are hot swappable; they can be installed while the switch is receiving power from the supply in the other slot. But, as indicated by the caution statement on the power supply, the supply must not be connected to AC power before being installed. Caution: .Refer to the installation guide for proper power cord selection. .Disconnect AC power from this power supply BEFORE installing or removing the supply. Otherwise, damage to the equipment may result. For safety and proper switch cooling, if either of the power supply slots are not being used, make sure to attach the cover plate over the slot. Please see the "Installation Precautions" on page 2-5 for more information. For installation details, see the instructions in the manual that comes with the power supply. 2-10

Section	Page
Installation and Getting Started Guide for the ProCurve Series 5300xl Switches	1
Title Page	3
Copyright and Disclaimer Notices	4
Contents	5
1. Introducing the ProCurve Switch 5300xl Series	9
Front of the Switch	12
LEDs	13
LED Mode Select Button and Indicator LEDs	15
Console Port	16
Reset Button	16
Clear Button	16
Back of the Switch	17
Power Connector	17
Slot for Redundant Power Supply	17
Switch Features	18
2. Installing the Switch 5300xl Series	21
Included Parts	21
Installation Procedures	23
Summary	23
1. Prepare the Installation Site	26
Cabling Infrastructure	26
Installation Location	27
2. Install Switch xl Modules	28
3. (Optional) Install Second Power Supply	30
4. Verify the Switch Passes Self Test	32
LED Behavior:	33
5. Mount the Switch	34
Rack or Cabinet Mounting	34
Horizontal Surface Mounting	36
Wall Mounting	37
6. Connect the Switch to a Power Source	38
7. Connect the Network Devices	38
8. (Optional) Connect a Console to the Switch	39
Terminal Configuration	39
Direct Console Access	40
Telnet Console Access	40
Hot Swapping Switch Modules	41
Adding or Replacing Modules	41
Changing the Module Type	41
Example Network Topologies	42
Basic Connectivity	42
Use as an Edge Switch	43
3. Getting Started With Switch Configuration	47
Recommended Minimal Configuration	47
Using the Switch Setup Screen	48
Where to Go From Here	50
Using the IP Address for Remote Switch Management	51
Starting a Telnet Session	51
Starting a Web Browser Session	51
Configuring the ProCurve Access Controller xl Module (J8162A)	53
740wl/760wl Configuration	53
Module Configuration	53
5300xl Switch Configuration	55
Configuring the ProCurve Wireless Edge Services xl Modules (J9001A, J9003A)	57
Configuring an IP Address for the Module	57
Configuring VLANs on the 5300xl Switch	59
Determining a Module Configuration Backup Process	59
Configuring Wireless LAN Services	59
4. Troubleshooting	61
Basic Troubleshooting Tips	61
Diagnosing with the LEDs	64
Proactive Networking	69
Hardware Diagnostic Tests	70
Testing the Switch by Resetting It	70
Checking the Switch LEDs	70
Checking Console Messages	70
Testing Twisted-Pair Cabling	71
Testing Switch-to-Device Network Communications	71
Testing End-to-End Network Communications	71
Restoring the Factory Default Configuration	72
Downloading New Code	73
HP Customer Support Services	73
Before Calling Support	73
A. Specifications	75
Physical	75
Electrical	75
Environmental	75
Acoustic	76
Switch 5308xl and Switch 5372xl:	76
Switch 5304xl and Switch 5348xl:	76
Network Connectors	76
Safety	76
B. Switch Ports and Network Cables	77
Switch Ports	77
Twisted Pair	77
Fiber-Optic	77
Cables	78
Fiber-Optic Cables	79
Copper Cables	80
Twisted-Pair Cable/Connector Pin-Outs	80
Straight-Through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections	82
Cable Diagram	82
Pin Assignments	82
Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection	83
Cable Diagram	83
Pin Assignments	83
Straight-Through Twisted-Pair Cable for 1000 Mbps Network Connections	84
Cable Diagram	84
Pin Assignments	84
C. Safety and EMC Regulatory Statements	85
Safety Information	85
Informations concernant la sécurité	86
Hinweise zur Sicherheit	87
Considerazioni sulla sicurezza	88
Consideraciones sobre seguridad	89
Safety Information (Japan)	90
Safety Information (China)	91
EMC Regulatory Statements	92
U.S.A.	92
Canada	92
Australia/New Zealand	92
Japan	92
Korea	93
Taiwan	93
Regulatory Model Identification Number	93
D. Recycle Statements	95
Waste Electrical and Electronic Equipment (WEEE) Statements	95
Index	99
Symbols	99
Numerics	99
A	99
B	99
C	99
D	100
E	100
F	100
G	101
H	101
I	101
L	101
M	102
N	102
O	102
P	102
R	103
S	103
T	104
V	104
W	104