HP J4819A User Manual - Page 55

xl Switch Configuration, <slot ID&gt

Get HP J4819A PDF manuals and user guides View all HP J4819A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Note Getting Started With Switch Configuration Configuring the ProCurve Access Controller xl Module (J8162A) 5300xl Switch Configuration Configuring the switch consists of assigning switch ports as client downlink ports and reviewing the uplink VLAN used by the module. The client downlink ports connect the module to clients, for example, access points. The uplink VLAN connects the module to the rest of the network and the 740wl/760wl. By default, it is assigned to the default_VLAN. To configure client downlink ports, from the CLI command prompt at the global configuration level ProCurve Switch 5308xl (config) # enter access-controller client-ports where is the slot letter where the module is installed. where is the port(s) to be used as client downlink ports. Each client downlink port is assigned to a separate, automatically created VLAN. If a port is already assigned to an untagged VLAN, it is reassigned as an untagged member of the new VLAN. If a port is a tagged member of an existing VLAN, it joins the new VLAN as an untagged member, while retaining its previous tagged VLAN membership. If you receive a message 'Command will take effect after saving configuration and reboot.' use write memory to save the configuration and reload to reboot the switch. If you have additional client ports to configure do so now, then save the configuration and reload the switch. To change the uplink VLAN from the default_VLAN, enter the configuration context for the new VLAN at the global configuration level ProCurve Switch 5308xl (config) # vlan assign the module's uplink to that VLAN as an untagged member ProCurve Switch 5308xl (config) (vlan ) # untagged up where is the slot where the module is installed. For example, if the module is in slot 'B' the command to assign the uplink VLAN to VLAN 3 would be ProCurve Switch 5308xl (vlan 3) # untagged bup Getting Started With Switch Configuration 3-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
3-9
Getting Started With Switch Configuration
Configuring the ProCurve Access Controller xl Module (J8162A)
Getting Started With Switch
Configuration
5300xl Switch Configuration
Configuring the switch consists of assigning switch ports as client downlink
ports and reviewing the uplink VLAN used by the module. The client downlink
ports connect the module to clients, for example, access points. The uplink
VLAN connects the module to the rest of the network and the 740wl/760wl.
By default, it is assigned to the default_VLAN.
To configure client downlink ports, from the CLI command prompt at the
global configuration level
ProCurve Switch 5308xl (config) #
enter
access-controller<slot ID> client-ports <port list>
where
<slot ID>
is the slot letter where the module is installed.
where
<port list>
is the port(s) to be used as client downlink ports.
Each client downlink port is assigned to a separate, automatically created
VLAN.
Note
If a port is already assigned to an untagged VLAN, it is reassigned as an
untagged member of the new VLAN. If a port is a tagged member of an existing
VLAN, it joins the new VLAN as an untagged member, while retaining its
previous tagged VLAN membership.
If you receive a message ‘Command will take effect after saving configuration
and reboot.’ use
write memory
to save the configuration and reload to reboot
the switch. If you have additional client ports to configure do so now, then
save the configuration and reload the switch.
To change the uplink VLAN from the default_VLAN, enter the configuration
context for the new VLAN at the global configuration level
ProCurve Switch 5308xl (config) # vlan <vid>
assign the module’s uplink to that VLAN as an untagged member
ProCurve Switch 5308xl (config) (vlan <vid>) # untagged <slotID>up
where
<slot ID>
is the slot where the module is installed. For example, if the
module is in slot ‘B’ the command to assign the uplink VLAN to VLAN 3 would
be
ProCurve Switch 5308xl (vlan 3) # untagged bup