HP ProLiant SL390s HP ProLiant SL390s G7 2U half width Server Maintenance and - Page 43

HP recommends using Shin-Etsu X-23-7783D thermal grease compound for your ProLiant

Get HP ProLiant SL390s - G7 Server PDF manuals and user guides View all HP ProLiant SL390s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Figure 21 Closing the processor socket CAUTION: To allow heat sink to draw as much heat as possible from the processor base, there must be good contact between the heat sink base and the top of the processor. To ensure good contact, you must apply thermal interface material. To apply the thermal grease compound: 1. Use the alcohol pad provided in the spare part kits or a clean cloth dipped in rubbing alcohol to clean the contact surface on the heat sink and on the new processor. Wipe the contact surfaces several times to make sure that no particles or dust contaminants are evident. CAUTION: HP recommends using Shin-Etsu X-23-7783D thermal grease compound for your ProLiant server. 2. Apply all the grease to the top of the processor in one of the following patterns to insure even distribution. Figure 22 Processor bottom CAUTION: Never touch the bottom of the processor; any contaminant could prevent the mounting pads from making contact with the socket. Removal and Replacement Procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Removal and Replacement Procedures 43
Figure 21
Closing the processor socket
CAUTION:
To allow heat sink to draw as much heat as possible from the processor base, there must
be good contact between the heat sink base and the top of the processor. To ensure good contact,
you must apply thermal interface material.
To apply the thermal grease compound:
1.
Use the alcohol pad provided in the spare part kits or a clean cloth dipped in rubbing alcohol to
clean the contact surface on the heat sink and on the new processor. Wipe the contact surfaces
several times to make sure that no particles or dust contaminants are evident.
CAUTION:
HP recommends using Shin-Etsu X-23-7783D thermal grease compound for your ProLiant
server.
2.
Apply all the grease to the top of the processor in one of the following patterns to insure even
distribution.
Figure 22
Processor bottom
CAUTION:
Never touch the bottom of the processor; any contaminant could prevent the mounting
pads from making contact with the socket.