HP ProLiant xw2x220c HP ProLiant xw2x220c Workstation Blade Maintenance and Se - Page 13

Hard drive

Get HP ProLiant xw2x220c - Blade Workstation PDF manuals and user guides View all HP ProLiant xw2x220c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

5. Turn jackscrew 1 approximately six turns counterclockwise. 6. Turn jackscrew 2 counterclockwise until the threads are fully disengaged. 7. Turn jackscrew 1 counterclockwise until the threads are fully disengaged. CAUTION: To prevent damage to the workstation blade, do not apply pressure to the enclosure connector. 8. Lift workstation B assembly from workstation A assembly, and then place it on the work surface with the system board facing up. Install workstation B assembly For access component identification, see "Access components (on page 47)." 1. Extend the workstation B serial label pull tab. 2. Engage the front edge of workstation B assembly with the front edge of workstation A assembly. CAUTION: Route the cache module battery cables so that they do not become pinched when the workstation B assembly is installed. 3. Lower workstation B assembly onto workstation A assembly. 4. Align the signal and power connectors on workstation B assembly with the corresponding connectors on workstation A assembly. CAUTION: The jackscrews control the unseating and seating of critical system connectors. Failure to use the jackscrews to remove and install the workstation B assembly can cause the system boards to fail. 5. Engage the threads on jackscrew 1 and tighten six turns clockwise. 6. Engage the threads on jackscrew 2 and tighten fully. 7. Tighten jackscrew 1 fully. Hard drive Removal and replacement procedures 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Removal and replacement procedures
13
5.
Turn jackscrew 1 approximately six turns counterclockwise.
6.
Turn jackscrew 2 counterclockwise until the threads are fully disengaged.
7.
Turn jackscrew 1 counterclockwise until the threads are fully disengaged.
CAUTION:
To prevent damage to the workstation blade, do not apply pressure to the
enclosure connector.
8.
Lift workstation B assembly from workstation A assembly, and then place it on the work surface with
the system board facing up.
Install workstation B assembly
For access component identification, see "Access components (on page
47
)."
1.
Extend the workstation B serial label pull tab.
2.
Engage the front edge of workstation B assembly with the front edge of workstation A assembly.
CAUTION:
Route the cache module battery cables so that they do not become pinched when
the workstation B assembly is installed.
3.
Lower workstation B assembly onto workstation A assembly.
4.
Align the signal and power connectors on workstation B assembly with the corresponding connectors
on workstation A assembly.
CAUTION:
The jackscrews control the unseating and seating of critical system connectors.
Failure to use the jackscrews to remove and install the workstation B assembly can cause the
system boards to fail.
5.
Engage the threads on jackscrew 1 and tighten six turns clockwise.
6.
Engage the threads on jackscrew 2 and tighten fully.
7.
Tighten jackscrew 1 fully.
Hard drive