HP ProLiant xw2x220c HP ProLiant xw2x220c Workstation Blade Maintenance and Se - Page 17

Processor

Get HP ProLiant xw2x220c - Blade Workstation PDF manuals and user guides View all HP ProLiant xw2x220c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3. Install the heatsink. 4. Install the workstation B assembly ("Install workstation B assembly" on page 13). 5. Install the workstation blade. Processor WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To avoid damage to the system board: • Do not touch the processor socket contacts. • Always install the processor socket cover after removing the processor from the socket. • Do not tilt or slide the processor when lowering the processor into the socket. CAUTION: To avoid damage to the processor: • Handle the processor only by the edges. • Do not touch the bottom of the processor, especially the contact area. CAUTION: To prevent possible workstation malfunction and damage to the equipment, multiprocessor configurations must contain processors with the same part number. CAUTION: To prevent possible workstation blade overheating, always populate processor socket 2 with a processor and a heatsink or a processor socket cover and a heatsink blank. CAUTION: The heatsink thermal interface media is not reusable and must be replaced if the heatsink is removed from the processor after it has been installed. IMPORTANT: When installing the heatsink, align the guide pins on the processor retention bracket with the alignment holes in the heatsink. Removal and replacement procedures 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Removal and replacement procedures
17
3.
Install the heatsink.
4.
Install the workstation B assembly ("
Install workstation B assembly
" on page
13
).
5.
Install the workstation blade.
Processor
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION:
To avoid damage to the system board:
•
Do not touch the processor socket contacts.
•
Always install the processor socket cover after removing the processor from the socket.
•
Do not tilt or slide the processor when lowering the processor into the socket.
CAUTION:
To avoid damage to the processor:
•
Handle the processor only by the edges.
•
Do not touch the bottom of the processor, especially the contact area.
CAUTION:
To prevent possible workstation malfunction and damage to the equipment,
multiprocessor configurations must contain processors with the same part number.
CAUTION:
To prevent possible workstation blade overheating, always populate processor
socket 2 with a processor and a heatsink or a processor socket cover and a heatsink blank.
CAUTION:
The heatsink thermal interface media is not reusable and must be replaced if the
heatsink is removed from the processor after it has been installed.
IMPORTANT:
When installing the heatsink, align the guide pins on the processor retention
bracket with the alignment holes in the heatsink.