HP ProLiant xw2x220c HP ProLiant xw2x220c Workstation Blade Maintenance and Se - Page 31

Workstation B system board

Get HP ProLiant xw2x220c - Blade Workstation PDF manuals and user guides View all HP ProLiant xw2x220c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

11. Record the workstation serial number and product ID. For the location of the serial number label, see "Workstation A system board components (on page 48)." 12. Install the workstation B assembly ("Install workstation B assembly" on page 13). 13. Install the workstation blade. After you replace the system board, you must re-enter the workstation serial number and the product ID. 1. During the workstation startup sequence, press the F9 key to access RBSU. 2. Select the System Options menu. 3. Select Serial Number. The following warning is displayed: WARNING! WARNING! WARNING! The serial number is loaded into the system during the manufacturing process and should NOT be modified. This option should only be used by qualified service personnel. This value should always match the serial number sticker located on the chassis. 4. Press the Enter key to clear the warning. 5. Enter the serial number and press the Enter key. 6. Select Product ID. 7. Enter the product ID and press the Enter key. 8. Press the Esc key to close the menu. 9. Press the Esc key to exit RBSU. 10. Press the F10 key to confirm exiting RBSU. The workstation will automatically reboot. Workstation B system board To remove the component: 1. Power down the workstation blade (on page 11). 2. Remove the workstation blade (on page 11). 3. Access the internal workstation components (on page 12). 4. Remove the workstation B USB key, if installed. 5. Remove the hard drive, if installed ("Hard drive" on page 13). 6. Remove all DIMMs ("DIMMs" on page 15). 7. Remove the heatsink ("Heatsink" on page 15). Removal and replacement procedures 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Removal and replacement procedures
31
11.
Record the workstation serial number and product ID. For the location of the serial number label, see
"Workstation A system board components (on page
48
)."
12.
Install the workstation B assembly ("
Install workstation B assembly
" on page
13
).
13.
Install the workstation blade.
After you replace the system board, you must re-enter the workstation serial number and the product ID.
1.
During the workstation startup sequence, press the
F9
key to access RBSU.
2.
Select the
System Options
menu.
3.
Select
Serial Number
. The following warning is displayed:
WARNING! WARNING! WARNING! The serial number is loaded into the system
during the manufacturing process and should NOT be modified. This option
should only be used by qualified service personnel. This value should
always match the serial number sticker located on the chassis.
4.
Press the
Enter
key to clear the warning.
5.
Enter the serial number and press the
Enter
key.
6.
Select
Product ID
.
7.
Enter the product ID and press the
Enter
key.
8.
Press the
Esc
key to close the menu.
9.
Press the
Esc
key to exit RBSU.
10.
Press the
F10
key to confirm exiting RBSU. The workstation will automatically reboot.
Workstation B system board
To remove the component:
1.
Power down the workstation blade (on page
11
).
2.
Remove the workstation blade (on page
11
).
3.
Access the internal workstation components (on page
12
).
4.
Remove the workstation B USB key, if installed.
5.
Remove the hard drive, if installed ("
Hard drive
" on page
13
).
6.
Remove all DIMMs ("
DIMMs
" on page
15
).
7.
Remove the heatsink ("
Heatsink
" on page
15
).