HP SignagePlayer mp8000r Maintenance & Service Guide: HP SignagePlayer mp8 - Page 132

TV Tuner Module, Preparation for Disassembly, on Computer Access Panel

Get HP SignagePlayer mp8000r PDF manuals and user guides View all HP SignagePlayer mp8000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

TV Tuner Module 1. Prepare the computer for disassembly (Preparation for Disassembly on page 92). 2. Remove the computer access panel (Computer Access Panel on page 99). 3. Remove the optical drive (Removing the Existing Optical Drive on page 107). 4. Remove the hard drive (Hard Drive on page 110). 5. Remove the hard drive cage (Hard Drive Cage on page 114). 6. Remove the heat sink (Heat sink on page 119). 7. Disconnect the antenna cable from the connector on the TV tuner module. 8. Remove the two Torx T5 screws that secure the TV tuner module to the system board. 9. Lift the card to a 45 degree angle, and then remove the module from the connector by pulling it away at an angle. Figure 7-34 Removing the TV tuner module To install the TV tuner module, reverse the removal procedure. Make sure the antenna cable is correctly routed over the speaker and in the clips mounted on the inside chassis wall. 122 Chapter 7 Removal and Replacement Procedures Ultra-Slim Desktop (USDT) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
TV Tuner Module
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
92
).
2.
Remove the computer access panel (
Computer Access Panel
on page
99
).
3.
Remove the optical drive (
Removing the Existing Optical Drive
on page
107
).
4.
Remove the hard drive (
Hard Drive
on page
110
).
5.
Remove the hard drive cage (
Hard Drive Cage
on page
114
).
6.
Remove the heat sink (
Heat sink
on page
119
).
7.
Disconnect the antenna cable from the connector on the TV tuner module.
8.
Remove the two Torx T5 screws that secure the TV tuner module to the system board.
9.
Lift the card to a 45 degree angle, and then remove the module from the connector by pulling it
away at an angle.
Figure 7-34
Removing the TV tuner module
To install the TV tuner module, reverse the removal procedure. Make sure the antenna cable is correctly
routed over the speaker and in the clips mounted on the inside chassis wall.
122
Chapter 7
Removal and Replacement Procedures Ultra-Slim Desktop (USDT) Chassis