HP SignagePlayer mp8000s Maintenance & Service Guide: HP SignagePlayer mp8 - Page 90

Front I/O, Power Switch Assembly

Get HP SignagePlayer mp8000s PDF manuals and user guides View all HP SignagePlayer mp8000s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Front I/O, Power Switch Assembly The front I/O and power switch/LEDs are one assembly, attached to the front of the chassis. Push the assembly into the chassis to remove. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 35). 2. Remove the access panel (Computer Access Panel on page 43). 3. Remove the front bezel (Front Bezel on page 44). 4. Remove the chassis fan (Front Fan Assembly on page 78). 5. Rotate the drive cage to its upright position. 6. Disconnect the four cables from the system board as follows: ● Yellow connector labeled FRNT USB1 ● Green connector labeled FRNT USB2 ● Blue connector labeled FRNT AUD ● Black connector labeled PB/LED 7. Remove the screw that secures the assembly to the front of the chassis. Figure 6-57 Removing the front I/O, power switch/LED assembly screw 80 Chapter 6 Removal and Replacement Procedures Small Form Factor (SFF) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Front I/O, Power Switch Assembly
The front I/O and power switch/LEDs are one assembly, attached to the front of the chassis. Push the
assembly into the chassis to remove.
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
35
).
2.
Remove the access panel (
Computer Access Panel
on page
43
).
3.
Remove the front bezel (
Front Bezel
on page
44
).
4.
Remove the chassis fan (
Front Fan Assembly
on page
78
).
5.
Rotate the drive cage to its upright position.
6.
Disconnect the four cables from the system board as follows:
●
Yellow connector labeled FRNT USB1
●
Green connector labeled FRNT USB2
●
Blue connector labeled FRNT AUD
●
Black connector labeled PB/LED
7.
Remove the screw that secures the assembly to the front of the chassis.
Figure 6-57
Removing the front I/O, power switch/LED assembly screw
80
Chapter 6
Removal and Replacement Procedures Small Form Factor (SFF) Chassis