HP StorageWorks 1606 Brocade Converged Enhanced Ethernet Command Reference v6.
HP StorageWorks 1606 - Extension SAN Switch Manual
View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 1606 manual content summary:
- HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 1
53-1001347-01 28 July 2009 Converged Enhanced Ethernet Command Reference Supporting Fabric OS v6.3.0 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 2
the programming source code, please visit http://www.brocade.com/support/oscd. Brocade Communications Systems, Incorporated Corporate and Latin American Headquarters Brocade Communications Systems, Inc. 1745 Technology Drive San Jose, CA 95110 Tel: 1-408-333-8000 Fax: 1-408-333-8101 E-mail: info - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 3
xv Chapter 1 CLI Basics In this chapter 1 Accessing the Brocade CEE Switch 1 CLI command modes 1 L2 ACL commands 3 Chapter 2 Configuration Management Commands copy 5 copy startup-config 6 delete 7 dir 8 disable 9 do 10 enable 11 end 12 erase flash 13 exec-timeout 14 Converged - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 4
19 pwd 20 rename 21 show calendar 22 show clock 23 show environment 24 show file 25 show line 26 show logging 27 show media 28 show -config 34 show system 35 show tech-support 36 show users 37 show version 38 terminal length 39 terminal monitor 40 write erase 41 write memory 42 VLAN - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 5
57 description 58 interface 59 mtu 60 show interface 61 show ip interface 63 shutdown 65 Link Layer Discovery Protocol Commands advertise dcbx hello 77 lldp dcbx-version 78 lldp disable 79 lldp fcoe-priority-bits 80 lldp profile 81 mode 82 multiplier 83 profile 84 protocol lldp 85 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 6
95 clear lacp counters 96 debug lacp 97 lacp system-priority 99 lacp timeout 100 show lacp counter 101 show lacp-sys-id 102 show port-channel 103 Layer 2 System Commands mac-address-table 105 show mac-address-table 107 Layer 2 ACL commands clear counters access-list mac 109 deny (extended - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 7
clear spanning-tree counter 127 debug spanning-tree 128 error-disable-timeout enable 129 error-disable-timeout interval 130 forward-delay 131 hello-time 132 instance 133 max-age 134 max-hops 135 port-channel path-cost 136 protocol spanning-tree 137 region 138 revision 139 show spanning- - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 8
qos rcv-queue interface 194 show qos rcv-queue multicast 195 Port Authentication Commands clear dot1x statistics 197 clear dot1x statistics interface 198 dot1x authentication 199 dot1x enable 200 dot1x port-control 201 dot1x quiet-period 202 dot1x reauthenticate interface 203 vi Converged - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 9
dot1x reauthentication 204 dot1x reauthMax 205 dot1x timeout re-authperiod 206 dot1x timeout server-timeout 207 dot1x timeout supp-timeout 208 dot1x timeout tx-period 209 show dot1x 210 show dot1x all 211 show dot1x diagnostics interface 213 show dot1x interface 214 show dot1x session-info - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 10
viii Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 11
access the switch and the CEE CLI command modes. • Chapter 2, "Configuration Management Commands"describes the commands to manage the configuration files and the commands to configure interfaces. • Chapter 5, "Link Layer Discovery Protocol Commands" describes the commands that support the Link Layer - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 12
Brocade FCOE10-24 port blade Within this manual, any appearance of the term "Brocade FCoE hardware" is referring to: • Brocade 8000 • Brocade FCOE10-24 port blade Although many different software and hardware configurations are tested and supported by Brocade Communications Systems, Inc. for Fabric - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 13
have been added for: • 802.1x Port Authentication For further information about new features and command names Identifies the names of user-manipulated GUI elements Identifies keywords and Command syntax conventions Command syntax in this manual follows these conventions: TABLE 1 Command syntax - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 14
Convention Description Nonprinting characters, for example passwords, appear in angle brackets [ ] Default responses to system prompts appear in square brackets. Notes, cautions, and warnings The following notices and statements are used in this manual. They are listed below in order of - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 15
get up-to-the-minute information, go to http://my.brocade.com and register at no cost for a user ID and password. For practical discussions about SAN design, implementation, and maintenance, you can obtain Building SANs with Brocade Fabric Switches through: http://www.amazon.com White papers, online - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 16
4100, 4900, 5100, 5300, 7500, 7800, 8000, and Brocade Encryption Switch-On the switch ID pull-out tab located inside the chassis on the port side on the left • Brocade 5000-On the switch ID pull-out tab located on the bottom of the port side of the switch • Brocade 7600-On the bottom of the chassis - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 17
an error or an omission, or you think that a topic needs further development, we want to hear from you. Forward your feedback to: [email protected] Provide the title and version number of the document and as much detail as possible about your comment, including the topic heading and page - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 18
xvi Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 19
to enter a login name and password. When you log on to a switch supporting CEE, all of the 10 Gbps ports are disabled and must be enabled. Refer to the Fibre Channel over Ethernet Administrator's Guide for information regarding feature configuration and management procedures. Following is an - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 20
CEE map: configuration switch (config-ceemap)# Standard ACL: switch (conf-macl-std)# Enter the cmsh command at the Fabric OS prompt after you have logged in as an appropriate user. Display running system information and set terminal line parameters. From the EXEC mode, enter the enable command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 21
Identify traffic based on the MAC-addresses, such as VLAN IDs and different encapsulations. • Configure multiple access-lists or rules and store them in a configuration. • IP packet data, such as protocols, TCP or UDP port numbers, type of service and to provide Reflective access-lists and Time-based - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 22
1 L2 ACL commands 4 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 23
FTP Copies to URL ftp://[username[:password]@server/path] SCP Copies to URL scp://[username[:password]@server/path] running-config Copies to the current running configuration. startup--config Copies to the current running configuration file. Defaults There are no usage guidelines for - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 24
password]@server/path] SCP Copies to URL scp://[username[:password]@server/path] running-config Copies to the current running configuration. Defaults There are no default configurations displays if there is no startup configuration file, for example: switch #copy startup-config file2 % Error - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 25
Operands filename Specifies the name of the file to be deleted from the Flash of the local switch using the following format: [flash://]filename. Defaults There is no default configuration for this command. Command Privileged EXEC mode Modes Description Use this command to delete a file from the - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 26
The default is the current directory. Command Privileged EXEC mode Modes Description Use this command to list the contents of the current directory. Usage There are no usage guidelines for this command. Guidelines Examples To list the contents of the current directory: switch#dir Contents - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 27
returns to the EXEC mode. Synopsis disable Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description EXEC mode: switch#disable switch> See Also enable, end, exit Converged Enhanced Ethernet Command Reference 9 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 28
Operands command Specifies the command you want to run. Defaults There are no default configurations for this command. Command All configuration modes Modes Description Use this command to save time when you are configuring the switch in any configuration mode and you want to run a command in - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 29
enable 2 enable Enables the Privilege EXEC mode. Synopsis enable Operands none Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command to enable . Examples To enable the Privileged EXEC mode: switch> enable switch# See Also disable - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 30
from all configuration modes. Synopsis end Operands none Defaults There are no default configurations for this command. Command All configuration modes Modes configuration mode: switch(config)#interface tengigabitethernet 0/0 switch(conf-if-te-0/0)#end switch# See Also exit, disable, enable - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 31
There are no default configurations for this command. Command Configuration mode Modes Description Use this command to erase the files from the Flash. Usage There are no usage guidelines for this command. Guidelines Examples To erase the files from the Flash: switch#erase flash %% Warning - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 32
the time interval in seconds. The range is 0-2147483. Defaults The default is 10 minutes. Command Console and VTY (line) configuration mode Modes Description Use this command to set the interval; the command interpreter waits for user input detected. Use no exec-timeout to disable the wait - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 33
previous mode. Synopsis exit Operands none Defaults There are no default configurations for this command. Command All configuration mode, and return to the Configuration mode: switch(config)#interface tengigabitethernet 0/0 switch(conf-if-te-0/0)#exit switch(config)#exit See Also end, enable - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 34
shell. Synopsis fos command Operands command Specifies the Fabric OS command. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to execute the following Fabric OS commands from the cmsh shell. alishow cfgactvshow - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 35
and fcoelogincfg commands are not supported from cmsh shell. See the Fabric OS Command Reference for additional information on these commands. Examples To run the Fabric OS command switchshow from the Privilege EXEC mode: switch#fos switchshow switchName: switch switchType: 76.6 switchState - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 36
virtual terminal line settings. Usage There are no usage guidelines for this command. Guidelines Examples To configure the wait interval for the console session: switch>enable switch#configure terminal switch(config)#line console 0 switch(config-line)#exec-timeout 2 30 switch(config-line)#exit - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 37
terminal line settings to set the exec-timeout. Usage There are no usage guidelines for this command. Guidelines Examples To configure the wait interval for the telnet session to time out after 2 minutes, 30 seconds if there is no response from the user: switch#configure terminal switch(config - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 38
There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to view the current working directory. Usage There are no usage guidelines for this command. Guidelines Examples To view the current working directory: switch#pwd flash: See - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 39
no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to rename a file in the Flash. Usage There are no usage guidelines for this command. Guidelines Examples To rename a file in the Flash: switch#rename file1 file2 switch#dir Contents - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 40
2 show calendar show calendar View the current date and time based on the switch hardware clock. Synopsis show calendar Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display the current date and - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 41
no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display the time and date from the system clock. Usage There are no usage guidelines for this command. Guidelines Examples To display the time and date from the system clock: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 42
2 show environment show environment Displays fan, temperature, redundant power system (RPS) availability, and power information for the switch. Synopsis show environment Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 43
default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display the contents of a text file in the local Flash. Usage There are no usage guidelines for this command. Guidelines Examples To show the file system for internal flash: switch#show - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 44
the last line number. The range of valid values is 0-31. Defaults If the line is not specified, it displays all VTY and console :1212 Length 24 24 24 24 24 24 24 24 24 24 24 24 24 24 switch#show line 0 Status Type Idle console 0 * Active vty 0 Timeout(m/s) 10:0 10:0 Length 24 24 See Also - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 45
syslog buffer of the switch. Synopsis show logging Operands none Defaults There are no default configurations for this command. . Interface TenGigabitEthernet 0/4 is Interface TenGigabitEthernet 0/4 is online. Interface Port-channel 10 is link down See Also none Converged Enhanced Ethernet - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 46
a switch. Synopsis show media Operands none Defaults There are no default configurations for this units 10 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 42:52:4f Vendor PN 57-0000075-01 Vendor Rev 0.002 (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) (output - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 47
port Specifies a valid port number. Defaults There are no default configurations interface: switch#show media 10 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 42:52:4f Vendor PN 57-0000075-01 Vendor 0.002 (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) See Also - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 48
Linecard number. Defaults There are no default configurations for this line card number 0: switch#show media linecard 0 meters) Length Cu 0 (units 1 meter) Vendor Name BROCADE Vendor OUI 42:52:4f Vendor PN 57-0000075-01 Vendor (mAmps) TX Power 0.1 (uWatts) RX Power 0.1 (uWatts) - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 49
Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display information about the active processes in the switch , 2009 5 kthread 0.00 S 14:18:35 Feb 19, 2009 40 kblockd/0 0.00 S 14:18:35 Feb 19, 2009 73 pdflush - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 50
Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to view memory usage information based KB To show memory usage information by individual processes: switch#show processes memory %Memory Used: 39.463%; TotalMemory: - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 51
Enhanced Ethernet (CEE) maps configuration. Displays the interface configuration. Displays the LLDP configuration. Displays the Remote Monitoring Protocol (RMON) configuration. Displays the switch configuration. Defaults There are no default configurations for this command. Command Privileged - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 52
startup configuration file. Synopsis show startup-config Operands none Defaults There are no default configurations for configuration file. • Using the write erase command to delete entries from startup configuration file. Examples To show the content of the startup configuration file: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 53
system Operands none Defaults There are no default configurations for this command. Port(s) Tengig Port(s) Up Time FOS Version Jumbo Capable Burned In MAC Management IP Status : switch : Online : 76.6 : 8 : 24 : 18:28:27 up 4:09 : v6.1.2 : yes : 00:05:1E:76:42:00 : 10.35.155.204 : UP -- Power - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 54
Inc. Build Time: 03:35:17 Feb 18, 2009 switch uptime: 04:11:09 Firmware name: v6.1.2 Switch Model Name: Brocade 8000 Control Processor: Freescale Semiconductor 8548E with 1016 MB of memory 4MB of boot flash memory. 8 FC Port(s) 24 Ten GigabitEthernet/IEEE 802.3 interface(s) show running-config - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 55
show users 2 show users Displays information on all users currently logged into the switch. Synopsis show users Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to view information on all users logged - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 56
18, 2009 E209 uptime: 04:14:43 Firmware name: v6.1.2 Switch Model Name: Brocade 8000 Control Processor: Freescale Semiconductor 8548E with 1016 MB of memory 4MB of boot flash memory. 8 FC Port(s) 24 Ten GigabitEthernet/IEEE 802.3 interface(s) switch# See Also show system 38 Converged Enhanced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 57
on a screen. The range of valid values is 0-512. Defaults The default length is 24. Command Privileged EXEC mode Modes Description Use this command to set the number of lines to display on the screen. Usage If 0 (zero), the switch does not pause between screens of output. Guidelines Examples - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 58
none Defaults The terminal monitor option is disabled. Command Privileged EXEC mode Modes Description Use this command to enable or for this command. Guidelines Examples To enable the display of the RASlog and the debug outputs on a terminal: switch#terminal monitor To disable the display - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 59
write erase Removes the startup configuration from the switch. Synopsis write erase Operands none Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to remove a startup configuration. Usage There are no usage - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 60
running configuration to the startup configuration file. Synopsis write memory Operands none Defaults There are no default configurations for Examples To write configuration data to a file: switch#write memory Overwrite the startup config file (y/n): y Building configuration... See Also write - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 61
fcf forward Operands none Defaults FCF forwarding is disabled. Command Interface VLAN mode Modes Description Use this command to enable FC forwarding on the command. Guidelines Examples To enable FC forwarding on a VLAN interface: switch(config)#interface vlan 777 switch(conf-if-vl-777)#fcf - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 62
of valid values is 1-3583. Defaults VLAN 1 is predefined on the switch. Command Global configuration mode Modes Description Use this command to configure a VLAN interface. Use the no interface vlan vlan_id command to delete a VLAN interface. Usage All of the ports on the switch are a part of the - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 63
. slot Specifies a valid slot number. port Specifies a valid port number. port-channel number Specifies the interface is a port-channel. The range of valid values is 1-63. switchport Specifies the Layer 2 interface. Defaults There are no default configurations for this command. Command EXEC - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 64
no default configurations for this command. Command Privileged EXEC mode Modes Description Use this command to display information about VLAN. Usage There are no usage guidelines for this command. Guidelines Examples To show information on a VLAN: switch#show vlan 1 VLAN Name State Ports - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 65
port Specifies a valid port number vlan vlan_id Specifies the VLAN to display. The range of valid values is 1-3583. Defaults There are no default configurations a specific configured VLAN classifier group is shown. Examples To display the VLAN classifier for group 1: switch#show vlan - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 66
Synopsis switchport no switchport Operands none Defaults By default, all Layer 2 interfaces are mapped to default VLAN 1 and the interface is set to access mode. Command Interface configuration mode Modes Description Use this command to set the switching characteristics of the Layer 2 interface - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 67
access vlan Operands vlan vlan_id Sets the port VLAN (PVID) to the specified vlan_id. The range of valid values is 1-3583. Defaults By default, all Layer 2 interfaces are in access mode and belong to the VLAN ID 1. Command Interface configuration mode Modes Description Use this command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 68
converged interface is 1. Command Interface configuration mode Modes Description Use this command to add or remove tagged VLANs on a Layer 2 interface. Usage There are no usage guidelines for this command. Guidelines Examples To set the native VLAN of 200 on an interface: switch(conf-if-te-0/19 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 69
There are no defaults for this command. Command Interface configuration mode Modes Description Use this command to set the mode of the Layer 2 interface. Usage There are no usage guidelines for this command. Guidelines Examples To set the mode of the interface to access: switch(conf-if-te - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 70
default configurations for this command. Command Interface configuration mode Modes Description Use this command to add or remove tagged VLANs on a Layer 2 interface. Usage There are no usage guidelines for this command. Guidelines Examples To set the tagged VLAN on an interface to 100: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 71
valid values is 1-3583. Defaults There are no default configurations for this command. Command Interface configuration mode Modes Description Use this command Guidelines Examples To activate VLAN classifier group 1 for VLAN 5: switch-cmsh(conf-if-te-0/10)#vlan classifier activate group 1 vlan - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 72
no default configurations for this command. Command Global configuration mode Modes Description Use this command to add and delete rules from VLAN classifier groups. Usage There are no usage guidelines for this command. Guidelines Examples To add rule 1 to VLAN classifier group 1: switch(config - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 73
arp| fcoe | fip| ip] [encap ethv2 | Defaults There are no default configurations for this command. Command Global configuration mode Modes Description Use this command to configure switch(config)#vlan classifier rule 2 proto fcoe encap ethv2 To create a MAC-based VLAN classifier rule: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 74
3 vlan classifier rule 56 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 75
interfaces: port-channel number Specifies the port-channel Brocade 8000 switch, the slot number is always 0 (zero). Description Use this command to clear statistics on one or on all interfaces. Defaults There are no default configurations for this command. Command Privileged EXEC mode Modes User - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 76
of characters is 64. Defaults There are no default configurations for this command. Command Interface configuration mode Modes Description Use this command. Guidelines Examples To set the string describing tengigabitethernet interface 0/1: switch(conf-if-te-0/1)#description converged_101 See - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 77
valid slot number. port Specifies a valid port number. port-channel number Specifies the port-channel number. The range of valid values is 1-63. vlan vlan_id Specifies the VLAN number. The range of valid values is 1-3583. Defaults There are no default configurations for this command. Command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 78
transmission unit (MTU) of an interface. The allowed MTU size is 1522-9208 bytes. Defaults By default, all 10 Gbps Ethernet interfaces use a default MTU of 2500 bytes. Command Interface configuration mode Modes Description Use this command to specify the MTU on the interface. Usage Creating - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 79
port Specifies to display a valid port number. switchport Specifies to display information for Layer 2 interfaces. Defaults There are no default configurations ifindex) is 67174401 MTU 2500 bytes LineSpeed: 10000 Mbit, Duplex: Full Flowcontrol rx: on, tx: on Last clearing of show interface - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 80
17 To display Layer 2 information for all interfaces: switch#show interface switchport Interface name Switchport mode Ingress filter Acceptable frame types Default Vlan Active Vlans Inactive Vlans : TenGigabitEthernet 0/8 : access : enable : all : 1 : 1 : - Interface name Switchport mode Ingress - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 81
to display a valid port number. vlan vlan_id Specifies to display a the VLAN number. The range of valid values is 1-3583. Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display IP interface status and configuration of all - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 82
4 show ip interface See Also TenGigabitEthernet 0/13 TenGigabitEthernet 0/14 TenGigabitEthernet 0/15 TenGigabitEthernet 0/16 TenGigabitEthernet 0/17 TenGigabitEthernet 0/18 TenGigabitEthernet 0/19 TenGigabitEthernet 0/20 TenGigabitEthernet 0/21 TenGigabitEthernet 0/22 TenGigabitEthernet 0/23 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 83
Defaults The interface is disabled. Command Interface configuration mode Modes Description Use this command to disable an interface. Usage There are no usage guidelines for this command. Guidelines Examples To disable an interface: switch(conf-if-te-0/1)#shutdown To enable an interface: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 84
4 shutdown 66 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 85
-fcoe-app-tlv Operands none Defaults Advertise is disabled. Command Protocol LLDP configuration mode Modes Description Use this command Use the no advertise dcbx-fcoe-app-tlv command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 86
Advertise is disabled. Command Protocol LLDP configuration mode Modes Description Use this command to advertise to any attached device the FCoE status of the logical link. Use the no advertise dcbx-fcoe-logical-link-tlv command to return to the default setting. Usage There are no usage guidelines - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 87
Advertise is enabled. Command Protocol LLDP configuration mode Modes Description Advertises to any attached device mandatory Data Center Bridging eXchange protocol (DCBX) Type, Length, Values (TLVs). Use the no advertise dcbx-tlv command to return to the default setting. Usage There are no - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 88
Advertise is disabled. Command Protocol LLDP configuration mode Modes Description Use this command to advertise to any attached device IEEE 802.1 organizationally specific Type, Length, Value (TLV). Use the no advertise dot1-tlv command to return to the default setting. Usage There are no usage - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 89
Advertise is disabled. Command Protocol LLDP configuration mode Modes Description Use this command to advertise to any attached device IEEE 802.3 organizationally specific Type, Length, Value (TLV). Use the no advertise dot3-tlv command to return to the default setting. Usage There are no usage - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 90
system. port-description Describes the user configured port. system-capabilities Specifies the capabilities of the system. system-description Describes the system firmware version and the current image running on the system. system-name Specifies the name of the system. Defaults Advertise is - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 91
slot Specifies a valid slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command Privileged . Examples To clear the LLDP information for all interfaces: switch#clear lldp neighbors See Also show lldp neighbors Converged Enhanced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 92
Specifies a valid slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command Privileged EXEC Examples To clear all the LLDP statistics for all interfaces: switch#clear lldp statistics See Also show lldp statistics 74 Converged Enhanced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 93
Gbps Ethernet interface. slot Specifies the slot number. port Specifies the port number. both Turns on debugging for both transmit and LLDP packets. Defaults By default, debugging is not turned on. Command Privileged EXEC mode Modes Description Use this command to enable debugging for Link - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 94
LLDP protocol. Defaults There are no default configurations for this command. Command Protocol LLDP configuration mode Modes Description for this command. Guidelines Examples To set the strings describing LLDP: switch(conf-lldp)#description Brocade-LLDP See Also none 76 Converged Enhanced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 95
Use the no hello command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To set the time interval to 10 seconds between the transmissions: switch#configure terminal switch (config) #protocol lldp switch(conf-lldp)#hello 10 See Also none - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 96
The default is auto. Command Interface configuration mode Modes Description Use this command to specify which version of the DCBX protocol to use. Usage There are no usage guidelines for this command. Guidelines Examples To specify which DCBX version to use: switch(conf-if-te-0/1)#lldp dcbx - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 97
lldp disable Disables LLDP on the interface. Synopsis lldp disable no lldp disable Operands none Defaults By default, LLDP is enabled at both the global and interface levels. Command Interface configuration mode Modes Description Use this command to disable LLDP on the interface. Use the no - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 98
-0xff. Defaults The default value is 0x08. Command Interface configuration mode Modes Description Use this command to set the priorities default setting. Usage There are no usage guidelines for this command. Guidelines Examples To set the priorities on which FCoE traffic will be allowed: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 99
profile name. Defaults If the parameters are not defined in the profile, the default values are used. Command Interface configuration mode Modes Description defined in the global LLDP configuration are used. Examples To apply an LLDP profile on an interface: switch(conf-if-te-0/1)#lldp profile - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 100
Operands tx rx Specifies to enable only the transmit mode. Specifies to enable only the receive mode. Defaults Both transmit and receive modes are enabled. Command Protocol LLDP configuration mode Modes Description Use this command to set the LLDP mode on the switch. Use the no mode command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 101
is 1-10. Defaults The default multiplier value is 4. Command Protocol LLDP configuration mode Modes Description Use this command to set the number of default setting. Usage There are no usage guidelines for this command. Guidelines Examples To set the number of consecutive misses: switch(conf - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 102
32 characters. Defaults none Command Protocol LLDP configuration mode Modes default global profile is used until you create a valid profile. Up to 64 profiles can be created. Examples To create a profile named test: switch(conf-lldp)#profile test To delete a profile named test: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 103
configuration mode. Synopsis protocol lldp no protocol lldp Operands none Defaults The LLDP and DCBX protocols are enabled. Command Global configuration default setting. Usage There are no usage guidelines for this command. Guidelines Examples To clear all LLDP configurations: switch(config - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 104
Displays the LLDP debugging status on the switch. Synopsis show debug lldp Operands none Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display the LLDP debugging status on the switch. Usage There are no usage guidelines - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 105
. port Specifies a valid port number. Defaults There are no default configurations for switch#show lldp interface tengigabitethernet 0/0 LLDP information for Te 0/0 State: Enabled DCBX FCoE Priority Bits: 0x8 Port ID IEEE DCBX DCBX FCoE Logical Link Brocade Link See Also none Converged Enhanced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 106
tengigabitethernet slot/port detail] Switch. System Capabilities: Switching Routing System Capabilities Enabled: Switching Link Prim: 257 Remote Protocols Advertised: Multiple Spanning Tree Protocol Remote VLANs Configured: VLAN ID: 1 VLAN Name: default AutoNego Support: Supported Not Enabled - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 107
Status: Disabled Port Vlan Id: 1 Port & Protocol Vlan Flag: Supported Not enabled Port & Protocol Vlan Id: 0 Link Aggregation Port Id: 0 Admin-Map: 0xf0 FCoE App OperVersion: 0 MaxVersion: 0 EN: 1 Will: 0 Err: 0 User-Pri-Map: 0x00 FCoE LLS OperVersion: 0 MaxVersion: 0 EN: 1 Will: 0 Err: 0 Logic - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 108
Specifies a valid slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command EXEC mode To display LLDP statistics on the specified interface: switch#show lldp statistics interface tengigabitethernet 0/8 LLDP Interface statistics - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 109
50 characters. Defaults There are no default configurations for this command. Command Protocol LLDP mode. Modes Description Use this command to set the global Guidelines Examples To set the global system description specific to LLDP: switch(conf-lldp)#system-description Brocade See Also system- - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 110
system name for the LLDP. The valid values is a maximum of32 characters. Defaults By default, the host name from the switch is used. Command Protocol LLDP configuration mode Modes Description Use this command to set the global system name specific to LLDP. Usage There are no usage guidelines for - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 111
-based LAG. Specifies the Brocade proprietary hardware-based trunking. Defaults By default, the type is set to standard. Command Interface configuration mode Modes Description Use this command to add an interface to a port-channel specified by the channel-group number. This command enables - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 112
6 channel-group See Also switch(conf-if)#channel-group 4 mode active interface port-channel 94 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 113
to clear the LACP counters per specified channel-group. Usage There are no default configurations for this command. Guidelines Examples To clear the LACP counters for a specific port-channel: switch#clear lacp 10 counters See Also show lacp counters Converged Enhanced Ethernet Command Reference - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 114
Description Use this command to clear the LACP counters for all port-channels. Usage There are no default configurations for this command. Guidelines Examples To clear the counters for all port-channels: switch#clear lacp counters See Also show lacp 96 Converged Enhanced Ethernet Command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 115
level number Specifies the trace level number. The range of valid values is 1-7. Defaults By default, debugging is not turned on. Command Privileged EXEC mode Modes Description Use this command to enable debugging for Link Aggregation Control Protocol (LACP). Use the no debug command to disable - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 116
6 debug lacp Examples See Also To enable debugging of LACP PDUs for transmitted and received packets on all interfaces: switch#debug lacp pdu tx all switch#debug lacp pdu rx all switch#show debug lacp LACP rx debugging is on LACP tx debugging is on show debug lacp 98 Converged Enhanced Ethernet - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 117
command to reset the system priority to the default value. Note Lower numerical values have higher priorities. Usage There are no usage guidelines for this command. Guidelines Examples To set the LACP system-priority to 68: switch(config)#lacp system-priority 68 To clear the configured LACP - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 118
timeout value. Defaults By default, the short timeout value is 3 seconds for Brocade trunks. For standard trunks, the long timeout value is 90 seconds. Command Interface configuration mode Modes Description Use this command to set the short timeout value for Brocade trunks or to set the long - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 119
the port-channel number to display. The range of valid values is 1-63. Defaults There are no default configurations for Guidelines Examples To show the LACP counters for port-channel 10: switch#show lacp counter 10 % Traffic statistics Port LACPDUs Marker Sent Recv Sent Recv % Aggregator - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 120
priority information. Synopsis show lacp sys-id Operands none Defaults There are no default configurations for this command. Command EXEC mode Modes Description the system. Examples To display the local system ID: switch#show lacp sys-id % System 8000,00-05-1e-76-1a-a6 See Also none 102 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 121
. Note LAG interfaces are called port-channels. Defaults There are no default configurations for this command. Command EXEC do not specify a port-channel, all port-channels are displayed. Guidelines Examples To display information for port-channel 10: switch#show port-channel 10 % Aggregator - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 122
6 show port-channel 104 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 123
values is 1-3583. Defaults The default aging time is 300 seconds. Command Global configuration mode Modes Description Use this command to set the aging time or to add static addresses to the MAC address table. Usage The vlan keyword is mandatory because the switch only supports independent VLAN - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 124
7 mac-address-table See Also To set the aging time to 10 minutes: switch(config)#mac-address-table aging-time 600 show mac address-table static 106 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 125
port Specifies a valid port number. static Displays the static MAC addresses. vlan vlan_id Specifies the VLAN number. The range of valid values is 1-3583. Defaults No static addresses are configured specific MAC address in the table: switch#show mac-address-table address 0011.2222.3333 Converged - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 126
-table See Also VlanId Mac-address Type 100 0011.2222.3333 Static Total MAC addresses : 1 State Inactive Ports Te 0/1 To display the aging time for a specific MAC address table: switch#show mac-address-table aging-time MAC Aging-time : 300 seconds To display a dynamic MAC address table - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 127
which have this ACL Guidelines applied are cleared. There are 255 ACL counters supported per port group. Example To clear counters for the configured MAC access list named test on an interface: switch#clear counters access-list mac test interface tengigabitethernet 0/1 To clear counters for the - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 128
mode Modes Description Use this command to configure rules to match and drop traffic based on the source and destination MAC addresses and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. Use the no deny command to - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 129
deny (extended ACLs) 8 See Also switch(conf-macl-ext)#no deny 0022.3333.4444 0022.3333.5555 ipv4 mac-access-list extended, mac-access-list standard, permit Converged Enhanced Ethernet Command Reference 111 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 130
. Command Feature Access Control List Configuration mode Modes Description Use this command to configure rules to match and to drop traffic based on the source MAC address. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. Use the no deny - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 131
the ACL is already created, this command puts the switch in the extended MAC access-list configuration mode. Use the no mac access-list extended command to remove the access list. Extended ACLs allow you to filter traffic based on - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 132
ACL is already created, this command puts the switch in the standard MAC access-list configuration mode. Use the no mac access-list standard command to remove the access list. Standard ACLs allow you to filter traffic based on the - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 133
filter inbound packets only. Default There are no access lists applied to the interface. Command Interface configuration mode Modes Description Use this with a MAC ACL applied, the switch checks the rules in the ACL. If any of the rules match, the switch permits or drops the packet, according - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 134
mode Modes Description Use this command to configure rules to match and to permit traffic based on the source and destination MAC addresses, and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. Use the no permit command to - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 135
permit (extended ACLs) 8 See Also To delete a filter rule in a MAC extended ACL: switch(conf-macl-ext)#no permit 0022.3333.4444 0022.3333.5555 ipv4 mac-access-list extended, mac-access-list standard, no seq Converged Enhanced Ethernet Command Reference 117 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 136
. Command Feature Access Control List Configuration mode Modes Description Use this command to configure rules to match and to permit traffic based on the source MAC address. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. Use the no permit - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 137
range of valid values is 1-65535. Defaults There are no default configurations for this command. Command Privileged EXEC mode switch#show running-config access-list mac test ! mac access-list standard test seq 10 permit 0011.2222.3333 seq 20 permit 0011.2222.4444 seq 30 permit 0011.2222.5555 seq 40 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 138
address for which to set permit or deny conditions. Use the format HHHH. configures rules to match and permits or drops traffic based on the source and destination MAC addresses, and the protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 139
source MAC address 0022.3333.4444 to the destination MAC address 0022.3333.5555 and to enable the counting of packets: switch(conf-macl-ext)#seq 100 deny 0022.3333.4444 0022.3333.5555 ipv4 count switch(conf-macl-ext)#seq 1000 permit 0022.3333.4444 0022.3333.5555 ipv4 count To delete - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 140
mode Modes Description Use this command to configure rules to match and permit or drop traffic based on source and destination MAC address and protocol type. You can also enable counters for a specific rule. There are 255 ACL counters supported per port group. Use the no seq value command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 141
port Specifies a valid port number. vlan vlan_id Specifies the VLAN number. The range of valid values is 1-3583. Defaults There are no default configurations no ACL applied: switch#show mac access-group interface tengigabitethernet 0/7 Interface Te 0/7 Inbound access-list is not set See Also show - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 142
port number. vlan vlan_idSpecifies the VLAN number. The range of valid values is 1-3583. Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display the active rules on the switch and whether those rules have counters enabled 40 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 143
command to return to the default settings. Usage This command must be used to specify the priority of the bridge. The priority values can be set only Guidelines in increments of 4096. Examples To specify the bridge priority: switch#configure terminal switch(config)#protocol spanning-tree stp - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 144
Configures the switch to interoperate with some legacy Cisco switches. Synopsis cisco-interoperability [disable| enable] Operands disable enable Disables Cisco interoperability for the Multiple Spanning Tree Protocol (MSTP) switch. Enables Cisco interoperability for the MSTP switch. Defaults - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 145
valid slot number. port Specifies a valid port number. Defaults There are no default configurations for this command. Command switch#clear spanning-tree counter interface tengigabitethernet 0/1 To clear spanning-tree counters for port-channel 23: switch#clear spanning-tree counter interface port - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 146
port Specifies the port number. Defaults By default debugging is not turned on. Command Privileged EXEC mode Modes Description Use this command to enable switch#debug spanning-tree bpdu rx interface tengigabitethernet 0/1 switch#debug spanning-tree bpdu tx interface tengigabitethernet 0/1 switch# - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 147
remains in the disabled state unless the port is enabled manually. This command allows you to enable the interface from the disabled state. Examples To bring the interface out of the disabled state: switch(conf-rstp)#error-disable-timeout enable See Also error-disable-timeout interval Converged - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 148
1000000. Defaults The default is 300 seconds. The timeout feature is disabled. Command Protocol Spanning Tree mode Modes Description Use this command to set the set the timeout value to 10 seconds: switch(conf-rstp)#error-disable-timeout interval 10 See Also error-disable-timeout enable - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 149
forward-delay command to return to the default settings. Note STP interface states: • Listening loop. • Blocking - An interface that can cause a switching loop, no user data is sent or received, but it might go to Examples To configure the forward-delay time to 18 seconds: switch(conf-mstp)# - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 150
devices. Use the no hello-time command to return to the default settings. Usage Guidelines When configuring the hello-time, the max-age setting must be greater than the hello-time setting. The following relationship should be kept: 2*(forward_delay - 1)>=max_age>=2*(hello_time + 1) Examples To - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 151
. The priority values can be set only in increments of 4096. Defaults The default priority value is 32768. Command configuration if the underlying VLANs are deleted. Examples To map a VLAN to an MTSP instance: switch(conf-mstp)#instance 1 vlan 2, 3 switch(conf-mstp)#instance 2 vlan 4-6 switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 152
-age max-age Sets the interval time in seconds between messages that the spanning tree receives from the interface. Synopsis max-age seconds no max-age Operands seconds Configures the Spanning tree Protocol interface maximum-age. The range of valid values is 6-40. Defaults The default is 20 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 153
valid values is 1-40. Defaults The default is 20 hops. Command Protocol Spanning Tree MSTP mode Modes Description Use this command to configure the maximum number of Examples To set the number of maximum hops to 25 for all MSTPs: switch(config)#protocol spanning-tree mstp switch(conf-mstp)# - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 154
The default path-cost is standard. Command Protocol Spanning Tree mode Modes Description Use this command to set the path-cost behavior for the port-channel. Usage There are no usage guidelines for this command. Guidelines Examples To set the behavior for the path-cost to custom: switch(conf - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 155
Protocol (STP). Defaults By default, STP is not enabled. STP is not required in a loop-free topology. Command Global configuration mode Modes before turning on Guidelines another form. Examples To enable the Spanning Tree Protocol: switch(config)#protocol spanning-tree stp See Also show - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 156
region-name Assigns a name to an MSTP region. Defaults There are no default configurations for this command. Command Protocol Spanning Tree MSTP mode Modes name to an MSTP region named brocade1: switch(config)#protocol spanning-tree mstp switch(conf-mstp)#region brocade1 See Also revision, show - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 157
number. Use the no revision command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To set the configuration revision to 1: switch(config)#protocol spanning-tree mstp switch(conf-mstp)#revision 1 See Also region, show spanning-tree - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 158
-guard errdisable timeout interval: 300 sec Migrate Time: 3 sec Port Te 0/0 enabled IfIndex: 67108864; Id: 8000; Role: Disabled; State: Discarding Designated External Path Cost: 0; Internal Path Cost 0 Configured Path Cost: 2000 Designated Port Id: 0; CIST Priority: 128 Designated Bridge: 0000.0000 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 159
Link-type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 Port Te 0/19 enabled IfIndex: 68354563; Id: 8013; Role: Disabled; State: Discarding Designated External Path Cost: 0; Internal Path Cost 0 Configured Path Cost: 2000 Designated Port Id: 0; CIST Priority: 128 Designated Bridge: 0000.0000.0000 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 160
default configurations for this command. Command EXEC mode Modes Description Use this command to display the status and parameters of the Spanning Tree Protocol. It includes the port roles and port states. The following describes the port roles and states: • Port roles-root port, designated port - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 161
: switch#show spanning-tree interface tengigabitethernet 0/0 Spanning-tree Mode: Rapid Spanning Tree Protocol Root Id: 8000.0005.1e76.1aa0 (self) Bridge Id: 8000.0005.1e76.1aa0 Port Te 0/0 enabled IfIndex: 67108864; Id: 8000; Role: Disabled; State: Discarding Designated Path Cost: 0 Configured - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 162
There are no default configurations for this command. Command EXEC mode Modes Description Use this command to display the status and parameters of the Multiple Spanning Tree Protocol (MSTP) instance information. It includes the port roles, port states and port types. Usage Guidelines The - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 163
: 300 sec Migrate Time: 3 sec CIST Port Details Instance: 0; Vlans:1, 100 Port Te 0/0 enabled IfIndex: 67108864; Id: 8000; Role: Disabled; State: Discarding Designated External Path Cost: 0; Internal Path Cost 0 Configured Path Cost: 2000 Designated Port Id: 0; CIST Priority: 128 Converged - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 164
Link-type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 Port Te 0/8 enabled IfIndex: 67633408; Id: 8008; Role: Disabled; State: Discarding Designated External Path Cost: 0; Internal Path Cost 0 Configured Path Cost: 2000 Designated Port Id: 0; CIST Priority: 128 Designated Bridge: 0000.0000.0000 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 165
show spanning-tree mst detail 9 See Also Link-type: point-to-point Received BPDUs: 0; Sent BPDUs: 0 MSTI details show spanning-tree mst interface, show spanning-tree mst instance Converged Enhanced Ethernet Command Reference 147 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 166
the interface for which to display information on the MSPT instance. port Specifies a valid port number for the interface for which to display information on the MSPT instance. Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 167
interface for which to display information for the MSTP instance. port Specifies a valid port number for the interface for which to display information for the MSTP instance. Defaults There are no default configurations for this command. Command EXEC mode Modes Description Use this command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 168
free topology and is not enabled by default. Command Protocol Spanning Tree mode Modes Description Use this command to disable the MSTP, RSTP, or STP protocol globally. Usage This command has no usage guidelines. Guidelines Examples To disable STP globally: switch(config)#protocol spanning-tree - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 169
-tree autoedge no spanning-tree autoedge Operands none Defaults Auto detection is not enabled. Command Interface configuration mode Modes Description Use this command to automatically identify the edge port. Usage The port can become an edge port if no Bridge Protocol Data Unit (BPDU) is - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 170
The default path cost is 200000000. Command Interface configuration mode Modes Description Use this command to configure the path cost for spanning-tree calculations. Usage Lower path cost indicates a greater chance of becoming root. Guidelines Examples To set the port cost to 128: switch(conf - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 171
bpdu-filter bpdu-guard Sets the edge port Bridge Protocol Data Unit (BPDU) filter for the port. Guards the port against the reception of BPDUs. Defaults Edge port is disabled. Command Interface configuration mode Modes Description Use this command to enable the edge port feature. This command is - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 172
be the spanning-tree root port or the path-to-the root for the switch. Synopsis spanning-tree guard root no spanning-tree guard root Operands none Defaults Guard root is disabled. Command Interface configuration mode Modes Description Use this command to enable the guard root on the interface - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 173
the hello Bridge Protocol Data Units (BPDUs) sent by the root switch configuration messages. The range of valid values 1-10. Defaults The default is 2 seconds. Command Interface configuration mode Modes Description Use this command to set the interval time between the BPDUs sent by the root - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 174
the propagation of the topology change notifications from a port. Defaults The default path-cost value is 2000 on a 10 Gbps Ethernet interface. Command Interface configuration mode Modes Description Use this command to set restrictions for a port on a particular MSTP instance. Usage Use this - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 175
-to-point. Command Interface configuration mode Modes Description Use this command to specify a link type for the Spanning Tree Protocol. Usage This command overrides the default setting of the link type. Guidelines Examples To specify the link type as shared: switch(conf-if-te-0/0)#spanning - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 176
bpdu-guard] Operands bpdu-filter bpdu-guard Sets the Port Fast BPDU filter for the port. Guards the port against the reception of BPDUs. Defaults Port Fast is disabled. Command Interface configuration mode Modes Description Use this command to enable the Port Fast feature. This command is is - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 177
priority. Use the no spanning-tree priority command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To configure the port priority to 16: switch(conf-if-te-0/1)#spanning-tree priority 16 See Also spanning-tree cost, show spanning-tree - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 178
. Use the no spanning-tree restricted-role command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To configure the port from becoming a root port: switch(conf-if-te-0/1)#spanning-tree restricted-role See Also show spanning-tree 160 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 179
change notification Bridge Protocol Data Units (BPDUs) sent on the port. Synopsis spanning-tree restricted-tcn no spanning-tree restricted-tcn Operands none Defaults The restricted TCN is disabled. Command Interface configuration mode Modes Description Use this command to restrict the topology - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 180
or disables spanning tree on the interface. Synopsis spanning-tree shutdown no spanning-tree shutdown Operands none Defaults Spanning tree is not enabled. Command Interface configuration mode Modes Description Use this command to disable spanning tree on the interface or VLAN. Use the no - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 181
spanning-tree tc-flush-standard no spanning-tree tc-flush-standard Operands none Defaults MAC address flushing is enabled. Command Global configuration mode Modes Description Use this command to flush the MAC address based on the optimal scheme. Use the no spanning-tree tc-flush-standard command - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 182
configure the BPDU burst size by changing the transmit hold count value. Use the no transmit-holdcount command to return to the default setting . Usage There are no usage guidelines for this command. Guidelines Examples To change the number of BPDUs transmitted to 3 seconds: switch( - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 183
name Specifies the identity of the owner. The maximum number of characters is 32. Defaults There are no alarms configured. Command Global configuration mode Modes Description Use this command to set alarm conditions. Use the no rmon alarm command to disable the alarm conditions. Usage There - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 184
10 rmon alarm See Also switch(config)#rmon alarm 100 1.3.6.1.2.1.16.1.1.1.5.65535 interval 5 absolute rising-threshold 10000 event 100 falling-threshold 1000 event 101 owner admin rmon event, show rmon 166 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 185
Specifies the identity of the owner. Defaults The collection of RMON statistics is not enabled. Command Interface configuration mode Modes Description Use this command on 10 Gbps Ethernet interface 0/1: switch(config)#interface tengigabitethernet 0/1 switch(conf-if-te-0/1)#rmon collection stats - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 186
string name to identify this trap. Defaults There are no events configured. Command Global configuration mode Modes Description Use this command to the event configuration. Usage There are no usage guidelines for this command. Guidelines Examples To configure an RMON event: switch(config)#rmon - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 187
are no default configurations for this command. Command EXEC mode Modes Description Use this command to display the status of the current RMON on the switch. Usage There are no usage guidelines for this command. Guidelines Examples To display the RMON statistics: switch#show rmon statistics - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 188
10 show rmon See Also Owner: RMON_SNMP Status: ok(1) To display the RMON events: switch#show rmon events event Index = 4 Description "My Description" Event type Log & SnmpTrap Event community name admin Last Time Sent = 00:00:00 Owner admin rmon - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 189
new one can be applied. Defaults There is no CEE Provisioning applied on an interface. Command Interface configuration mode Modes Description Use this command on the switch. Guidelines Examples To apply a CEE map on an interface: switch(conf-if-te-0/1)#cee demo Because the switch does not - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 190
Sets the precedence value for controlling the global scheduler policy when there is conflict between multiple CEE maps and non-CEE QoS configurations. The range of valid values is 1-100. Defaults The default create a CEE map: switch(config)#cee-map test To delete a CEE map: switch(config)#no cee-map - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 191
percent. The range of valid values is 1-100. Enables the Priority-based Flow Control (PFC) for each priority that gets mapped to the Priority Group. Defaults There is no default value for the weight. The PFC is disabled. Command CEE map configuration mode Modes Description Use this command to - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 192
Sets the Priority Group ID for all packets with CoS 6. Sets the Priority Group ID for all packets with CoS 7. Defaults The default CEE Priority mapping table matches the IEEE 802.1Q recommendation for systems supporting PGID 15.0). Command CEE Map Configuration mode Modes Description Use this - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 193
priority-table 11 See Also switch(config)#ceemap test switch(conf-ceemap)#priority-table 1 1 0 0 1 1 1 15.0 cee, cee-map, priority-group-table Converged Enhanced Ethernet Command Reference 175 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 194
is used to assign a CoS value to all Guidelines untagged packets entering the interface. Examples To set the interface CoS value to 2: switch(conf-if-te-0/2)#qos cos 2 To return the interface CoS value to the default: switch(conf-if-te-0/2)#no qos cos See Also show qos, qos map, qos trust 176 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 195
map. Defaults There is no explicit CoS-to-CoS mutation QoS map applied; by default the inbound CoS equals the outbound CoS. Command Interface configuration mode Modes to-CoS mutation QoS map on the interface: switch(conf-if-te-0/1)#qos cos-mutation test To remove the CoS-to-CoS mutation QoS - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 196
Defaults There is no explicit CoS-to-Traffic Class QoS map applied; the implicit behavior is to match the IEEE 802.1Q recommendations for systems supporting eight Traffic Classes. Command Interface configuration -Traffic Class QoS map to an interface: switch(int Te 0/2)#qos cos-traffic-class test - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 197
Sets the outbound CoS value for all packets with inbound CoS 7. Defaults There are no CoS-to-CoS mutation QoS maps defined. Command Global configuration . The inbound CoS value is the user priority after any interface ingress QoS trust and Interface default CoS policy have been applied. The - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 198
11 qos map cos-mutation See Also qos cos-mutation, show qos maps 180 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 199
Class. The outbound CoS value is used as the packet user priority after applying the configured interface QoS trust, interface default CoS, and CoS-to-CoS mutation policies. Traffic Class is a reference to a scheduler queue and packet servicing policy. Use the no qos map cos-traffic-class name - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 200
The default weight value is 25 percent bandwidth for each multicast Traffic Class. Command Global configuration mode Modes Description Use this command to configure the multicast Traffic Class packet expansion scheduler policy. All multicast Traffic Class packet expansion queues are serviced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 201
weight4 weight5 weight6 weight7 no qos queue scheduler strict-priority Configures the Strict Priority Traffic Class policy. All Strict Priority Traffic Classes are serviced before any DWRR Traffic Classes. strict-priority number Sets the number of the Strict Priority Traffic Class. These are - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 202
no default value for each weight value. Command Global configuration mode Modes Description Use this command to configure the Traffic Class packet scheduler policy. Eight Traffic Classes are supported with a configurable number of them being Strict Priority and any remaining ones being serviced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 203
across the entire system. This rate limit is enforced independently by each switch. Use the no qos rcv-queue multicast rate-limit command to return the multicast packet expansion rate limit to the default settings. Usage There are no usage guidelines for this command. Guidelines Examples To - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 204
is 0-2047 packets. Sets the Tail Drop Threshold for multicast Traffic Class 3 packet expansion queue in units of packets (pkt). The range of valid values is 0-2047 packets. .Defaults The default is 64 packets for each multicast Traffic Class. Command Global configuration mode Modes Description - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 205
configuration mode Modes Description Use this command to specify the interface ingress QoS trust mode, which controls user priority mapping of incoming traffic. The untrusted mode overrides all incoming priority markings with the Interface Default CoS. The CoS mode sets the user priority based - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 206
for this command. Guidelines Examples To display information on all of the defined CEE maps: switch#show cee maps CEE Map test Precedence 1 Priority Group Table 0: Weight 50, PFC Enabled, TrafficClass 4, BW% 50 1: Weight 50, PFC Disabled, TrafficClass 2, BW% 50 15.0: PFC Disabled, TrafficClass - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 207
number within the chassis. port Specifies the 10 Gbps Ethernet port number within the linecard. linecard configured flow control information for a 10 Gbps Ethernet interface: switch#show qos flowcontrol interface tengigabitethernet 0/1 Interface TenGigabitEthernet 0/1 Mode PFC DCBX enabled - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 208
is displayed. Guidelines Examples To display all of the configured QoS information for a 10 Gbps Ethernet interface: switch#show qos interface tengigabitethernet 0/1 Interface TenGigabitEthernet 0/1 Provisioning mode cee CEE Map demo Default CoS 0 Interface trust cos CoS-to-CoS Mutation map - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 209
show qos interface 11 See Also Traffic Class Scheduler configured for 0 Strict Priority queues TrafficClass: 0 1 2 3 4 5 6 7 DWRRWeight: 0 0 0 0 60 0 40 0 Multicast Packet Expansion Traffic Class Scheduler TrafficClass: 0 1 2 3 DWRRWeight: 25 25 25 25 cee-map, priority table Converged Enhanced - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 210
Traffic Class QoS maps. Defaults The default behavior without any specified configuration state is displayed with a list of all interfaces bound to the QoS map. Usage There are no usage guidelines for this command. Guidelines Examples To display information on the defined QoS maps: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 211
10 Gbps Ethernet interface linecard slot number. port Specifies the 10 Gbps Ethernet interface port number within the linecard. all Reports bytes sent and received for each priority. Usage For a stand-alone switch, all ASICs are considered as slot number zero (0). Guidelines Examples To - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 212
linecard slot number. port Specifies the 10 Gbps Ethernet interface port number within the linecard. all Reports QoS configurations for all 10 Gbps from the dataplane for a 10 Gbps Ethernet interface: switch#show qos rcv-queue interface tengigabitethernet 0/2 Interface TenGigabitEthernet - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 213
port Specifies the 10 Gbps Ethernet interface port number within the linecard. all Reports QoS multicast packet expansion receive queueing statistics for all ASICs within the system. Defaults There are no default configurations depth. Usage For a stand-alone switch, all ASICs are considered as - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 214
11 show qos rcv-queue multicast 196 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 215
are no defaults for this command. Command Global configuration mode Modes Description Use this command to clear all accumulated port authentication statistics on all ports. Usage There are no usage guidelines for this command. Guidelines Examples To clear dot1x statistics: switch(config)#clear - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 216
are no defaults for this command. Command Global configuration mode Modes Description Use this command to clear all of the dot1x statistics for a specific interface port. Usage There are no usage guidelines for this command. Guidelines Examples To clear dot1x statistics on a port: switch(config - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 217
authentication 12 dot1x authentication Enables dot1x on a port. Synopsis dot1x authentication no dot1x authentication Operands none Defaults There are no defaults for this command. Command Interface configuration mode Modes Description Use this command to enable dot1x on a port. Use the no - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 218
12 dot1x enable dot1x enable Enables 802.1X authentication globally. Synopsis dot1x enable no dot1x enable Operands none Defaults By default, authentication is disabled globally. Command Global configuration mode Modes Description Use this command to globally enable 802.1X authentication. - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 219
Interface configuration mode Modes Description Use this command to control the authorization of a port state. Use the no dot1x port-control command to return to the default setting. Usage There are no usage guidelines for this command. Guidelines Examples To enable the port state to auto: switch - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 220
at authentication. The range of valid values is 1-65535. Defaults The default time is 60 seconds. Command Interface configuration mode Modes Description Use this command to set the time in seconds after which a switch attempts to perform authentication after a failed authentication. Use the - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 221
Operands name Specifies the name of the interface. Defaults There are no defaults for this command. Command Privileged EXEC mode Modes Examples To initiate reauthentication on interface tengigabitethernet 0/1: switch#dot1x reauthenticate interface tengigabitethernet 0/1 See Also none - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 222
none Defaults There are no defaults for this command. Command Interface configuration mode Modes Description Use this command to enable reauthentication on a port. Usage There are no usage guidelines for this command. Guidelines Examples To enable reauthentication on a port: switch(config - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 223
valid values is 1-10. Defaults The default number of times that a port attempts authentication is two. Command Interface configuration mode Modes Description Use this command to set the maximum number of times that a port attempts to reauthenticate before a port changes to the unauthorized state - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 224
1-65535. Defaults The default time is 3600 seconds. Command Interface configuration mode Modes Description Use this command to set the number Examples To set 25 seconds as the amount of time between reauthorization attempts: switch(config)#interface tengigabitethernet 0/1 switch(conf-if- - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 225
values is 1-65535. Defaults The default timeout is 30 seconds. Command Interface configuration mode Modes Description Use this command to set the authentication sever response timeout. Usage There are no usage guidelines for this command. Guidelines Examples To set 40 seconds as the switch-to - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 226
valid values is 1-65535. Defaults The default timeout is 30 seconds. Command Interface configuration mode Modes Description Use this command to specify the EAP response timeout. Usage There are no usage guidelines for this command. Guidelines Examples To set 45 seconds as the switch-to-client - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 227
in seconds between successive request ID attempts. The range of valid values is 1-65535. Defaults The default timeout is 30 seconds. Command Interface configuration mode Modes Description Use this command to set the interval between successive attempts to request an ID (EAP ID Req). Usage There - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 228
Operands none Defaults There are no defaults for this command switch#show dot1x 802.1X Port-Based Authentication Enabled PAE Capability: Authenticator Only Protocol Version: 2 Auth Server: RADIUS RADIUS Configuration Position: Server Address: Port: Secret: Position: Server Address: Port - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 229
To display detailed information for all of the ports: switch#show dot1x all 802.1X Port-Based Authentication Enabled PAE Capability: Authenticator Only Protocol Version: 2 Auth Server: RADIUS RADIUS Configuration Position: Server Address: Port: Secret: 1 172.21.162.51 1812 sharedsecret - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 230
12 show dot1x all See Also none 212 Converged Enhanced Ethernet Command Reference 53-1001347-01 - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 231
with a port. Synopsis show dot1x diagnostics interface name Operands name Specifies the name of the interface. Defaults There are no defaults for this diagnostics information for the authenticator associated with a port: switch#show dot1x diagnostics interface tengigabitethernet 0/1 802.1X - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 232
name Operands name Specifies the name of the interface. Defaults There are no defaults for this command. Command EXEC mode Modes Description Use switch#show dot1x interface tengigabitethernet 0/1 Dot1x Global Status: Enabled 802.1X info for interface te0/1 Port Control: Auto Port - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 233
Operands name Specifies the name of the interface. Defaults There are no defaults for this command. Command EXEC mode Modes Description the established session: switch#show dot1x session-info interface tengigabitethernet 0/1 802.1X Session info for te0/1 User Name: testuser Session - HP StorageWorks 1606 | Brocade Converged Enhanced Ethernet Command Reference v6. - Page 234
are no defaults for this command. Command EXEC mode Modes Description Use this command to display the statistics of a specified interface. Usage There are no usage guidelines for this command. Guidelines Examples To display the statistics for 10 Gbps Ethernet interface 0/1: switch#show dot1x
53-1001347-01
28 July 2009
Converged Enhanced
Ethernet Command
Reference
Supporting Fabric OS v6.3.0