HP Tc2100 HP Server Novell NetWare Installation Guide (including v 6.5) - Page 18

Performing a new installation, Default, Manual, <F1&gt, Continue, Modify, Free Space, Enter - server ram

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Performing a new installation Inspect the system to confirm that it meets the minimum RAM and disk space requirements needed for installation. 1. Power on the server. 2. Insert the NetWare 6.5 Operating System CD. Note After booting the NetWare 6.5 CD, if an existing NetWare installation is detected a message will appear prompting you to either (I) Install or (R) Run NetWare. Choose option I so that the existing installation will be replaced. 3. When prompted, select the appropriate Language to install. 4. Select the proper regional settings for your location. 5. Accept the NetWare 6.5 and Report Runtime license agreements. 6. Select either Default or Manual as the installation type. The Default installation automatically detects drivers and installs the server with default settings. The Manual installation allows you to configure settings and modify detected drivers. 7. Press at this screen to see more details on both installation methods. 8. Choose the method that best suits your network environment. 9. The steps below outline the Manual installation procedure. 10. For Express installations, select Continue on the two Installation Type screens and proceed to step 22. below. 11. Create a Boot Partition. 12. Select Modify to create a boot partition. 13. Select Free Space, and press Enter. 14. Enter a DOS partition size between 500 MB and 2 GB. While a 500 MB DOS partition is typically adequate, a larger DOS partition size will allow larger NetWare Core Dumps to be created for problem analysis. 15. Wait for the DOS partition to be formatted, and then select Continue. 16. Confirm the Server settings shown by selecting Continue.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
Performing a new installation
Inspect the system to confirm that it meets the minimum RAM and disk space requirements needed
for installation.
1. Power on the server.
2.
Insert the NetWare 6.5 Operating System CD.
Note
After booting the NetWare 6.5 CD, if an existing NetWare
installation is detected a message will appear prompting you to
either (I) Install or (R) Run NetWare. Choose option I so that the
existing installation will be replaced.
3.
When prompted, select the appropriate Language to install.
4.
Select the proper regional settings for your location.
5.
Accept the NetWare 6.5 and Report Runtime license agreements.
6. Select either
Default
or
Manual
as the installation type. The Default installation
automatically detects drivers and installs the server with default settings. The Manual
installation allows you to configure settings and modify detected drivers.
7. Press
<F1>
at this screen to see more details on both installation methods.
8.
Choose the method that best suits your network environment.
9.
The steps below outline the Manual installation procedure.
10. For Express installations, select
Continue
on the two Installation Type screens and proceed
to step 22. below.
11. Create a Boot Partition.
12. Select
Modify
to create a boot partition.
13. Select
Free Space
, and press
Enter
.
14. Enter a DOS partition size between 500 MB and 2 GB. While a 500 MB DOS partition is
typically adequate, a larger DOS partition size will allow larger NetWare Core Dumps to
be created for problem analysis.
15. Wait for the DOS partition to be formatted, and then select
Continue
.
16. Confirm the Server settings shown by selecting
Continue
.