Husqvarna RZ54i Owners Manual - Page 36

Headlights, Weak Battery, Jumper Cables Use, To remove cables

Get Husqvarna RZ54i PDF manuals and user guides View all Husqvarna RZ54i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

OPERATION Headlights Use Button 2 to turn on/off the headlights. When the engine is in start mode, press the button to turn the headlights on. A blinking Button 2 light signals that one or both headlights are not working. The headlights can also be used when the ignition switch is not activated or the unit is not running. Press Button 2 and the headlights will stay lit for one minute. For a longer headlight mode, press and hold the button for five seconds. The headlights will flash twice to acknowledge and will stay on for five minutes. Headlight button 8058-239 Weak Battery WARNING! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. If the battery is too weak to start the engine, it should be recharged. (See Battery in the Maintenance section.) Jumper Cables Use 1. Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis. 2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery. 3. Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery away from the fuel tank and battery. To remove cables 4. Remove BLACK cable first from chassis and then from the fully charged battery. 5. Remove RED cable last from both batteries. Jumper cable connection 8011-642 IMPORTANT INFORMATION Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
36
OPERATION
Headlights
Use Button 2 to turn on/off the headlights. When the
engine is in start mode, press the button to turn the
headlights on. A blinking Button 2 light signals that
one or both headlights are not working.
The headlights can also be used when the ignition
switch is not activated or the unit is not running. Press
Button 2 and the headlights will stay lit for one minute.
For a longer headlight mode, press and hold the
button for five seconds. The headlights will flash twice
to acknowledge and will stay on for five minutes.
8058-239
Headlight button
Weak Battery
8011-642
Jumper cable connection
IMPORTANT INFORMATION
Your mower is equipped with a 12-volt negative
grounded system. The other vehicle must also
be a 12-volt negative grounded system. Do not
use your mower to start other vehicles.
WARNING!
Lead-acid batteries generate
explosive gases. Keep sparks, flame
and smoking materials away from
batteries. Always wear eye protection
when around batteries.
If the battery is too weak to start the engine, it should
be recharged. (See
Battery
in the
Maintenance
section.)
Jumper Cables Use
1.
Connect each end of the RED cable to the
POSITIVE (+) terminal on each battery, taking
care not to short against chassis.
2.
Connect one end of the BLACK cable to the
NEGATIVE (-) terminal of the fully charged battery.
3.
Connect the other end of the BLACK cable to a
good CHASSIS GROUND on the mower with the
discharged battery away from the fuel tank and
battery.
To remove cables
4.
Remove BLACK cable first from chassis and then
from the fully charged battery.
5.
Remove RED cable last from both batteries.