Husqvarna ST 230 Owner Manual - Page 13

To operate the product, To stop the product, To use the throttle control, Remove the ON/OFF key.

Get Husqvarna ST 230 PDF manuals and user guides View all Husqvarna ST 230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

10. Disconnect the extension cord from the receptacle first and then from the engine. 11. Run the engine 2-3 minutes at idling speed before you start to throw snow. To operate the product CAUTION: Do not operate without snow or water to lubricate the auger blades. Incorrect use can cause high temperatures in the auger blades, especially if the product is new. This can cause damage to the auger blades and scraper bar. C B CAUTION: Do not partially engage drive or auger levers for an extended period of time; this can lead to premature wear or burning of the belts. Note: When both the drive engagement and auger engagement are engaged, the drive engagement will lock the auger engagement in position. Use the right hand to control the snow discharge chute. 4. To make the product move in the selected direction, hold the drive engagement (C) against the handle . 5. If the product has power steering, hold the left steering trigger (D) to turn left. Hold the right steering trigger to turn right. Note: Do not change the speed when the drive lever is engaged. This can cause damage to the transmission. 1. To engage the auger blades, push the auger engagement (A) to the handle to engage the auger and throw snow. A D To stop the product 1. Move the ON/OFF switch to the OFF position (if equipped). 2. Remove the ON/OFF key. To use the throttle control • Turn the throttle control (A) to change the amount of fuel used. Always operate the engine at full throttle. 2. Raise the drive speed control lever (B) from the middle position to make the product move forward when the drive engagement (C) is engaged. Do not change the speed when the drive lever is engaged. This can cause damage A to the transmission. 3. Lower the drive speed control lever from the middle position to make the product move rearward when the drive engagement is engaged. L TRO N CO CTHROUCKTEIONS 694 - 003 - 07.11.2019 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
10. Disconnect the extension cord from the
receptacle first and then from the engine.
11. Run the engine 2-3 minutes at idling speed
before you start to throw snow.
To operate the product
CAUTION:
Do not operate without snow
or water to lubricate the auger blades.
Incorrect use can cause high
temperatures in the auger blades,
especially if the product is new. This can
cause damage to the auger blades and
scraper bar.
CAUTION:
Do not partially engage drive
or auger levers for an extended period of
time; this can lead to premature wear or
burning of the belts.
Note:
When both the drive engagement and auger
engagement are engaged, the drive engagement will
lock the auger engagement in position. Use the right
hand to control the snow discharge chute.
Note:
Do not change the speed when the drive lever
is engaged. This can cause damage to the
transmission.
1.
To engage the auger blades, push the auger
engagement (A) to the handle to engage the
auger and throw snow.
A
2.
Raise the drive speed control lever (B) from the
middle position to make the product move
forward when the drive engagement (C) is
engaged. Do not change the speed when the
drive lever is engaged. This can cause damage
to the transmission.
3.
Lower the drive speed control lever from the
middle position to make the product move
rearward when the drive engagement is
engaged.
C
B
4.
To make the product move in the selected
direction, hold the drive engagement (C) against
the handle .
5.
If the product has power steering, hold the left
steering trigger (D) to turn left. Hold the right
steering trigger to turn right.
D
To stop the product
1.
Move the ON/OFF switch to the OFF position (if
equipped).
2.
Remove the ON/OFF key.
To use the throttle control
•
Turn the throttle control (A) to change the
amount of fuel used. Always operate the engine
at full throttle.
CHOKE
CONTROL
TRUCTIONS
A
694 - 003 - 07.11.2019
13