Husqvarna ST 230 Owner Manual - Page 18

Drive belts, To prepare for replacement of the belts, To remove the drive belt

Get Husqvarna ST 230 PDF manuals and user guides View all Husqvarna ST 230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

A B 2. Replace the scraper bar if it is worn on both sides or if it is damaged. Drive belts WARNING: The v-belts on your product are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest service center. Using other than OEM belts can cause personal injury or damage to the product. WARNING: The belt replacement requires separation of the product. While separating the auger housing from the frame, it is important that an assistant stands in the operating position and holds the product handles. Serious personal injury and/or damage to the product could occur if the product falls during the belt replacement process. A C 3. Loosen the two screws (A) that secure the belt cover (B) to the frame (C) and remove the belt cover. C A Note: The auger and traction drive belts are not adjustable. Replace the belts if they are damaged or begin to slip from wear. It is recommended to have the belts replaced by a qualified service center. Note: It is recommended to replace the drive belt and auger belt at the same time. To prepare for replacement of the belts 1. Remove the fuel from the fuel tank. 2. Loosen the lock nut (A) that secures the chute rotator head (B) to the mounting bracket (C) to remove the discharge chute. B To remove the drive belt 1. Remove the auger belt. See To remove the auger belt on page 19. 2. Remove the tensioner spring (A) attached to the drive belt tensioner arm (B). E G F B H A I C J D 3. Remove the return spring (C) holding the swing plate (D) in place. 18 694 - 003 - 07.11.2019

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
A
2.
Replace the scraper bar if it is worn on both
sides or if it is damaged.
Drive belts
WARNING:
The v-belts on your product
are of special construction and should be
replaced by original equipment
manufacturer (OEM) belts available from
your nearest service center. Using other
than OEM belts can cause personal
injury or damage to the product.
WARNING:
The belt replacement
requires separation of the product. While
separating the auger housing from the
frame, it is important that an assistant
stands in the operating position and
holds the product handles. Serious
personal injury and/or damage to the
product could occur if the product falls
during the belt replacement process.
Note:
The auger and traction drive belts are not
adjustable. Replace the belts if they are damaged or
begin to slip from wear. It is recommended to have
the belts replaced by a qualified service center.
Note:
It is recommended to replace the drive belt
and auger belt at the same time.
To prepare for replacement of the belts
1.
Remove the fuel from the fuel tank.
2.
Loosen the lock nut (A) that secures the chute
rotator head (B) to the mounting bracket (C) to
remove the discharge chute.
B
A
C
3.
Loosen the two screws (A) that secure the belt
cover (B) to the frame (C) and remove the belt
cover.
C
A
B
To remove the drive belt
1.
Remove the auger belt. See
To remove the
auger belt on page 19
.
2.
Remove the tensioner spring (A) attached to the
drive belt tensioner arm (B).
A
B
C
D
E
H
F
G
I
J
3.
Remove the return spring (C) holding the swing
plate (D) in place.
18
694 - 003 - 07.11.2019