IBM 84903bu User Guide - Page 48

peripheral

Get IBM 84903bu - Servers X Series P4 3.4ghz PDF manuals and user guides
UPC - 000435882073
View all IBM 84903bu manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

To install a simple-swap hard disk drive, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 19. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords. 3. Unlock the side cover (the bezel will not disengage from the server if the cover is locked). 4. Remove the side cover and lower bezel (see "Removing the side cover" on page 22 and "Removing the two-piece bezel" on page 23). 5. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 6. Align the drive assembly with the guide rails in the bay (the connector end of the drive goes in first). 7. Pull the loops of the drive assembly toward each other; then, carefully slide the drive assembly into the drive bay until it stops and release the loops. Note: Do not release the loops on the drive assembly until it is completely seated. If you have other options to install or remove, do so now; otherwise, go to "Completing the installation" on page 44. 34 xSeries 206m Types 8485 and 8490: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
To
install
a
simple-swap
hard
disk
drive,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
19.
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
external
cables
and
power
cords.
3.
Unlock
the
side
cover
(the
bezel
will
not
disengage
from
the
server
if
the
cover
is
locked).
4.
Remove
the
side
cover
and
lower
bezel
(see
“Removing
the
side
cover”
on
page
22
and
“Removing
the
two-piece
bezel”
on
page
23).
5.
Touch
the
static-protective
package
that
contains
the
drive
to
any
unpainted
metal
surface
on
the
server;
then,
remove
the
drive
from
the
package
and
place
it
on
a
static-protective
surface.
6.
Align
the
drive
assembly
with
the
guide
rails
in
the
bay
(the
connector
end
of
the
drive
goes
in
first).
7.
Pull
the
loops
of
the
drive
assembly
toward
each
other;
then,
carefully
slide
the
drive
assembly
into
the
drive
bay
until
it
stops
and
release
the
loops.
Note:
Do
not
release
the
loops
on
the
drive
assembly
until
it
is
completely
seated.
If
you
have
other
options
to
install
or
remove,
do
so
now;
otherwise,
go
to
“Completing
the
installation”
on
page
44.
34
xSeries
206m
Types
8485
and
8490:
User’s
Guide