IBM 8687 Installation Guide - Page 136

A new NetWare Bus Interface driver, NBI.NLM, from, Install NetWare and the Gigabit Ethernet driver

Page 136 highlights

Known problems with NetWare are: NetWare 5.1 is currently not supported, but it should still install. See RETAIN tip H176163 for details on a known shutdown problem: http://www.pc.ibm.com/qtechinfo/MIGR-43679.html With NetWare 6.0, the server may show extreme CPU utilization values (for example, 13000%). This will be fixed with NetWare 6.0 Support Pack 2. See RETAIN tip H176060 at: http://www.pc.ibm.com/qtechinfo/MIGR-43532.html The overall process is as follows: 1. Install NetWare and the Gigabit Ethernet driver 2. Apply the latest NetWare Support Pack 3. Install additional drivers 4. Add support for the RXE100 5. Enable Hyper-Threading You will need the following device drivers: Broadcom Gigabit Ethernet, from http://www.pc.ibm.com/qtechinfo/MIGR-43369.html Remote Supervisor Adapter, from http://www.pc.ibm.com/qtechinfo/MIGR-42317.html IBM Active PCI driver, from http://www.pc.ibm.com/qtechinfo/MIGR-42423.html A new NetWare Bus Interface driver, NBI.NLM, from http://support.novell.com/filefinder/ (search for NBIUP1.EXE) To install NetWare 6 on x440, do the following: 1. Disconnect the RXE-100 if you have one attached. You should reconnect it after the Support Pack is installed and before the NBI driver is installed. 2. Power on the x440 with bootable NetWare 6 CD in the CD-ROM drive. 3. Follow the NetWare installer screen instructions up to the device driver screen, shown in Figure 4-10 on page 123. The NetWare installer cannot detect the Broadcom Gigabit controller. 122 IBM ^ xSeries 440 Planning and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202

122
IBM
^
xSeries 440 Planning and Installation Guide
Known problems with NetWare are:
±
NetWare 5.1 is currently not supported, but it should still install. See RETAIN
tip H176163 for details on a known shutdown problem:
±
With NetWare 6.0, the server may show extreme CPU utilization values (for
example, 13000%). This will be fixed with NetWare 6.0 Support Pack 2. See
RETAIN tip H176060 at:
The overall process is as follows:
1.
Install NetWare and the Gigabit Ethernet driver
2.
Apply the latest NetWare Support Pack
3.
Install additional drivers
4.
Add support for the RXE100
5.
Enable Hyper-Threading
You will need the following device drivers:
±
Broadcom Gigabit Ethernet, from
±
Remote Supervisor Adapter, from
±
IBM Active PCI driver, from
±
A new NetWare Bus Interface driver, NBI.NLM, from
(search for NBIUP1.EXE)
To install NetWare 6 on x440, do the following:
1.
Disconnect the RXE-100 if you have one attached. You should reconnect it
after the Support Pack is installed and before the NBI driver is installed.
2.
Power on the x440 with bootable NetWare 6 CD in the CD-ROM drive.
3.
Follow the NetWare installer screen instructions up to the device driver
screen, shown in Figure 4-10 on page 123. The NetWare installer cannot
detect the Broadcom Gigabit controller.