Icom IC-7300 Instruction Manual basic

Icom IC-7300 Manual

Get Icom IC-7300 PDF manuals and user guides View all Icom IC-7300 manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-7300 manual content summary:

  • Icom IC-7300 | Instruction Manual basic - Page 1
    BASIC MANUAL HF/50 MHz TRANSCEIVER i7300
  • Icom IC-7300 | Instruction Manual basic - Page 2
    completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL- This instruction manual contains full operating instructions for the IC-7300. FEATURES ••RF Direct Sampling System The IC-7300 employs an RF direct sampling system. RF signals are directly converted to digital data and
  • Icom IC-7300 | Instruction Manual basic - Page 3
    uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions antenna. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia
  • Icom IC-7300 | Instruction Manual basic - Page 4
    CD The following items are included on the CD. ••Full manual (English) Instructions for full operations, the same as the manual on the supplied CD. ••Basic manual (English) Instructions for basic operations, the same as this manual. ••Basic manual (German, Spanish, French, Italian, and other
  • Icom IC-7300 | Instruction Manual basic - Page 5
    THE INSTRUCTIONS The Full and Basic manuals are described in the following manner. " " (Quotation marks): Used to indicate icons, setting items, and screen titles displayed on the screen. The screen titles are also indicated in uppercase letters. (Example: FUNCTION screen) [ ] (brackets):  Used to
  • Icom IC-7300 | Instruction Manual basic - Page 6
    iii ABOUT THE SUPPLIED CD iii ABOUT THE INSTRUCTIONS iv PRECAUTIONS power supply ........ 2-3 Connecting the antenna tuner 2-3 3 BASIC OPERATION 3-1 When first applying power 3-1 Turning power ON or OFF 3-1 Adjusting the volume level 3-1 About the VFO and Memory modes 3-1 Using the VFO mode
  • Icom IC-7300 | Instruction Manual basic - Page 7
    6-2 Formatting an SD card 6-2 7 ANTENNA TUNER OPERATION 7-1 About the internal antenna tuner 7-1 Internal antenna tuner operation 7-1 DDManual tuning 7-1 DDPTT Tuner start 7-1 8 SET MODE 8-1 Set mode description 8-1 DDEntering the Set mode 8-1 Tone Control 8-2 Function 8-3 Connectors
  • Icom IC-7300 | Instruction Manual basic - Page 8
    periods of time. CAUTION: If you use a linear amplifier, set the transceiver's RF output power to less than the linear amplifier's maximum input level, otherwise a high input could damage the linear amplifier. CAUTION: Use only Icom supplied or optional microphones. Other manufacturer's microphones
  • Icom IC-7300 | Instruction Manual basic - Page 9
    use to operate the IC-7300. Refer to the pages posted beside each key, control, or dial for details. 1 2 3 q 4 w e 5 !9 r 6 t 7 y 8 u i o !0 !1 !2 !3 !4 !5 !6 !7 !8 9 10 q POWER KEY POWER ANTENNA TUNER KEY TUNER (p. 7-1) Turns the antenna tuner ON or OFF, or activates the tuner
  • Icom IC-7300 | Instruction Manual basic - Page 10
    Pad. @1 VFO/MEMORY KEY V/M (p. 3-1) Switches between the VFO and Memory mode, or copies the memory channel contents to the VFO. @2 CLEAR KEY CLEAR Clears to monitor the transmit frequency while holding it down in the Split mode. @9 TX/RX INDICATOR (p. 3-9) Lights red while transmitting and
  • Icom IC-7300 | Instruction Manual basic - Page 11
    power cable. w GROUND TERMINAL [GND] (p. 2-1) Connects to ground to prevent electrical shocks, TVI, BCI and other problems. e ANTENNA Icom linear amplifier. 14 !1 TUNER CONTROL SOCKET [TUNER] (p. 2-2) 15 Accepts the control cable from an optional AH-4 or AH-740 automatic antenna tuner
  • Icom IC-7300 | Instruction Manual basic - Page 12
    so on that are displayed on the IC-7300 screen. Refer to the pages posted beside each item for details. q w e r t y u i o !0 !1 !2 !3 !4 !5 q TUNE ICON (p. 7-1) Appears while tuning the antenna. w MODE INDICATOR (p. 3-2) Displays the selected operating mode. e PASSBAND WIDTH INDICATOR
  • Icom IC-7300 | Instruction Manual basic - Page 13
    5-1) Displayed while using the Spectrum Scope. @0 FUNCTION DISPLAY Displays the operating parameters, modes, frequencies and indicators, while transmitting. •• appears when the selected frequency is outside of the band edge frequency range. 18 •• TX appears when transmission is inhibited
  • Icom IC-7300 | Instruction Manual basic - Page 14
    menu items SSB SSB-D CW RTTY RF POWER RF POWER RF POWER RF POWER MIC GAIN MIC GAIN KEY SPEED TPF* COMP* CW PITCH MONITOR* adjust. DDFUNCTION screen Function name Selected value Lights blue or orange when used FUNCTION screen zzOpen the FUNCTION screen by pushing FUNCTION . LTo close
  • Icom IC-7300 | Instruction Manual basic - Page 15
    KEYER MEMORY A to Z, 0 to 9, (space 70 "*" (asterisk) has its unique use. FUNCTION RTTY MEMORY A to Z, 0 to 9, (space 70 VOICE TX RECORD A to < > 8 DDKeyboard types 9 You can select the Full Keyboard or Tenkey in "Keyboard Type" on the FUNCTION alphabet mode or number mode Enters
  • Icom IC-7300 | Instruction Manual basic - Page 16
    1 PANEL DESCRIPTION Keypad entering and editing (Continued) DDEntering and editing example Entering "DX spot 1" in the Memory channel 2 1. Open the MEMORY screen. MENU » MEMORY 2. Touch the memory channel 2 for 1 second. ••Opens the QUICK MENU. 3. Select "Edit Name." You can also open the QUICK
  • Icom IC-7300 | Instruction Manual basic - Page 17
    interference (TVI), broadcast 7 interference (BCI) and other problems, ground the transceiver 8 using the ground terminal [GND] on the rear panel. connector 18 19 SM-50 (Option) SM-30 (Option) HM-219 (Supplied) Using an External Keypad You can control the CW memory keyer, Voice memory or
  • Icom IC-7300 | Instruction Manual basic - Page 18
    mm: 1/4 in (d)) You can use a straight or bug key when the internal electronic keyer is OFF. [GND] (Ground) Grounding prevents electrical shock, TVI and other problems. [ANT] (antenna) connector Connect a 50 Ω antenna for the HF, 50/70 MHz frequency bands. [TUNER] control socket (p. 2-3) Connect
  • Icom IC-7300 | Instruction Manual basic - Page 19
    11 IC-7300 12 Fuses Supplied DC 13 Red Black power cable 14 Connecting the antenna tuner The AH-4 automatic antenna tuner matches the IC-7300 to the optional AH-2b or a long wire antenna more than 7 m/23 ft long (between 3.5 MHz and 50 MHz). 15 16 LSee the AH-4 instruction manual for
  • Icom IC-7300 | Instruction Manual basic - Page 20
    . ••DC power cable ••Antenna ••Grounding wire ••Microphone* *Different devices may be used, depending on the operating mode. If all POWER for 2 seconds until "POWER OFF..." is displayed. Adjusting the volume level Rotate AF RF/SQL (inner) to adjust the volume level. Using the VFO mode The IC-7300
  • Icom IC-7300 | Instruction Manual basic - Page 21
    and modes on the selected band. DDUsing the band stacking registers Follow the steps below to enter a register on the selected band. (Example: Memorizing 21 MHz) 1. Touch the MHz digits. (Example: 14) ••Opens the BAND STACKING REGISTER screen. 2. Touch a band key. (Example: [21]) BAND STACKING
  • Icom IC-7300 | Instruction Manual basic - Page 22
    step of 1 Hz for fine tuning in the SSB, CW and RTTY modes. Touch the Hz digits for 1 second to turn the Fine Tuning function ON or OFF. ••The 1 Hz digit is displayed. 1Hz digit The Tuning Step function is ON. LWhen using the [UP]/[DN] keys on the microphone, the frequency changes in 50
  • Icom IC-7300 | Instruction Manual basic - Page 23
    the frequency (Continued) DDAbout the 1/4 Tuning function Mode: SSB-D/CW/RTTY With the Tuning Function OFF, turn frequency 1. Touch the MHz digits. 3 (Example: 14) 4 5 6 ••Opens the BAND STACKING REGISTER screen. 2. Touch [F-INP]. 7 8 9 10 BAND STACKING REGISTER screen ••Opens the
  • Icom IC-7300 | Instruction Manual basic - Page 24
    screen. 2. Touch [F-INP]. Entering a Memory channel 1. Touch V/M to select the Memory mode. V/M VFO mode (Example: VFO A) Memory mode (Example: Memory channel 1) 2. Touch the MHz digits. (Example: 14) BAND STACKING REGISTER screen ••Opens the F-INP screen. 3. Enter the Split Frequency Offset
  • Icom IC-7300 | Instruction Manual basic - Page 25
    and returns to the 17 previous screen. 18 19 20 21 TIP: ••You can also edit the frequency by rotating MAIN DIAL or MULTI . ••Each band edge must be higher in frequency than the ones above it. If you try to enter a lower frequency than the edge above, the lower frequency
  • Icom IC-7300 | Instruction Manual basic - Page 26
    000 - 1.999.999 MHz) Entering a new Band Edge After you delete or edit the preset band edges, you can enter a new band edge. 1. Open the "User Band Edge" screen. 2. Select a blank band. (Example: 10) Rotate Push "User Band Edge" screen 3. Enter the lower band edge frequency. (Example: 51.15
  • Icom IC-7300 | Instruction Manual basic - Page 27
    edges to their initial settings. All entered settings will be deleted. 9 1. Open the "User Band Edge" screen. 10 2. Touch any band edge for 1 second. 11 12 13 "User Band Edge" screen 3. Touch "Default." 14 15 16 17 18 ••Displays "Reset All Edges?" 19 4. Touch [YES]. ••All
  • Icom IC-7300 | Instruction Manual basic - Page 28
    amateur practice to listen first, and then, even if nothing is heard, ask if the frequency in use once or twice, before you start operating. DDAdjusting the transmit output power 1. Set the operating mode to SSB, CW, RTTY or FM. (p. 3-2) (Example: USB) 2. Touch the meter to display the Po meter
  • Icom IC-7300 | Instruction Manual basic - Page 29
    . Po: Displays the relative RF output power. SWR:  Displays the SWR of the antenna at the frequency. ALC: Displays at your normal voice level. •• In the AM or FM mode, check the audio clarity with another station, or use the Monitor function (p. 4-8). 6. Push TRANSMIT or release [PTT].
  • Icom IC-7300 | Instruction Manual basic - Page 30
    , USB Data, PSK, and CW modes. ••Maximum of 100 watts ERP (Effective Radiated Power) ••Maximum 2.8 kHz bandwidth It is your responsibility to set all controls so that transmission in this frequency band meets the stringent conditions under which amateur operations may use these frequencies. TIP: We
  • Icom IC-7300 | Instruction Manual basic - Page 31
    to-noise ratio and sensitivity. A preamp is used when receiving weak signals. LEach band memorizes the Preamplifier setting. Push P.AMPATT (P.AMP RIT function turns ON. 4 LWhile using the Fine Tuning function (p. 3-3), the RIT frequency is displayed in 4 digits, instead of 3. 5 LPushing RIT
  • Icom IC-7300 | Instruction Manual basic - Page 32
    AGC (SSB) screen. 4. Touch either FAST, MID or SLOW to select the desired AGC to adjust the time constant. (Example: MID) AGC (SSB) screen (SSB mode) You can reset to the default settings by touching this key for 1 second. 5. Rotate MAIN DIAL to set the time constant. LThe adjustable time
  • Icom IC-7300 | Instruction Manual basic - Page 33
    Twin PBT SSB, CW, RTTY and AM modes In general, the Twin PBT (Passband Tuning) electronically narrows the IF passband width by shifting the IF frequency to slightly outside of the IF filter passband, to reject interference. The IC-7300 uses DSP for the PBT function. You can narrow the IF passband
  • Icom IC-7300 | Instruction Manual basic - Page 34
    setting value is reset to the center position. Passband width mode Touch for 1 second to reset to default. Displayed when a band width less than 500 Hz is selected in the SSB or CW mode. 6. Touch [BW]. ••Cancels the passband width mode. 7. Repeat steps 2 to 6 to set the passband width for other
  • Icom IC-7300 | Instruction Manual basic - Page 35
    picking up very weak signals in the 50 MHz band, for example. The shape factor is kept, and the performance. This function optimizes the Analog/Digital Converter (ADC) against the distortion be used in the FM mode. 2 Push NB to turn the Noise Blanker ON or OFF. 3 Displayed 4 NOTE: When using
  • Icom IC-7300 | Instruction Manual basic - Page 36
    Reduction ON NR level 4 Desired signal (CW) Notch Filter The IC-7300 has Auto Notch and Manual Notch functions. Auto Notch: Used in the SSB, AM and FM modes. Manual Notch: Used in the SSB, CW, RTTY and AM modes. DDAuto Notch function Auto Notch automatically attenuates beat tones, tuning signals
  • Icom IC-7300 | Instruction Manual basic - Page 37
    This function enables hands-free operation. DDAdjusting the VOX function Before using the VOX function, adjust the following items. ••VOX GAIN ••ANTI "LONG" or OFF. 13 14 DDTurning ON the VOX function 15 1. Set the operating mode to SSB, AM or FM. (Example: USB) 16 2. Push VOX/BK-IN to
  • Icom IC-7300 | Instruction Manual basic - Page 38
    ∂TX function ON or OFF. LWhile using the Fine Tuning function (p. 3-3), the ∂TX frequency is displayed in 4 digits, instead of 3. ∂TX frequency 2.  directly monitor the operating frequency by holding down XFC . FUNCTION screen (USB mode) 4. Touch [MONI] for 1 second. 5. Adjust MONITOR to the
  • Icom IC-7300 | Instruction Manual basic - Page 39
    4 RECEIVING AND TRANSMITTING Setting the Speech Compressor SSB mode The Speech Compressor increases the average RF output power, improving readability at the receiving station. This function compresses the transmitter audio input to increase the average audio output level. LThe function is
  • Icom IC-7300 | Instruction Manual basic - Page 40
    different bands. Another station There are 2 ways to use the Split frequency operation. ••Use the Quick Split function ••Use the the Split function. 1. Set VFO A's receive frequency and operating mode. (Example: 21.29000 MHz in the USB mode) 2. Hold down SPLIT for 1 second. ••The Quick Split
  • Icom IC-7300 | Instruction Manual basic - Page 41
    ] sets the filter width to WIDE, MID or NAR. FUNCTION screen (SSB mode) LThe transmit filter widths are set to the following values by default. •• suit your preference without changing the operating frequency. 2 1. Select the CW mode. 3 2. Display the Multi-function menu. 4 Push 5 6 3. Touch
  • Icom IC-7300 | Instruction Manual basic - Page 42
    48 Words Per Minute (WPM). Rotate Push DDAbout the Break-in function Use the Break-in function in the CW mode to automatically switch between transmit and receive when keying. The IC-7300 is capable of Semi Break-in and Full break-in modes. TIP: The key type is set to "Paddle" by default. You can
  • Icom IC-7300 | Instruction Manual basic - Page 43
    BKIN" is displayed. LPushing VOX/BK-IN selects "BKIN (Semi Break-in)," "F-BKIN (Full Break-in)" or OFF (no indication). Full Break-in 3. Using a straight key or paddle. LIn the Full break-in mode, the transceiver automatically returns to receive without a preset break-in delay time after you stop
  • Icom IC-7300 | Instruction Manual basic - Page 44
    1. Open the KEYER screen in the CW mode. MENU » KEYER LYou can select [KEYER] on the MENU screen only in the CW mode. 2. Touch [EDIT/SET]. ••Opens the exactly to another station's by matching the audio tone. ••You can also use the CW side tone (make sure the Break-in function is OFF (p.
  • Icom IC-7300 | Instruction Manual basic - Page 45
    the contents set in the RTTY TX memory, you can operate the basic RTTY operation without using an external device. LIf you are using PSK software, refer to the software manual. 1. Select the RTTY mode. 2. Open the RTTY DECODE screen. MENU » DECODE LYou can select [DECODE] on the MENU screen only
  • Icom IC-7300 | Instruction Manual basic - Page 46
    4 RECEIVING AND TRANSMITTING Operating RTTY (FSK) (Continued) DDFunctions on the RTTY DECODE screen Open the RTTY DECODE screen in the RTTY mode. MENU » DECODE TIP: Touching [EXPD/SET] toggles between the Normal screen and Expanded screen. Normal screen DDSetting the decoder threshold level
  • Icom IC-7300 | Instruction Manual basic - Page 47
    You can access a repeater using the split function. 1. Select the desired operating band. (p. 3-2) (Example: 28 MHz band) 2. Rotate MAIN DIAL to the FM mode. 2. Push FUNCTION . 4 ••Opens the FUNCTION screen. 3. Touch [TONE] for 1 second. 5 6 7 8 FUNCTION screen (FM mode) ••Opens the
  • Icom IC-7300 | Instruction Manual basic - Page 48
    band, as well as the relative strengths of various signals. The IC-7300 has two spectrum scope modes. One is the Center mode, and another one is the Fixed mode 1 seco­ nd to select the ±2.5 kHz span. EDGE In the Fixed mode, selects the Edge frequencies. LYou can set the Upper and lower Edge
  • Icom IC-7300 | Instruction Manual basic - Page 49
    the SPECTRUM SCOPE screen. MENU » SCOPE DDFixed mode Displays signals within a specified frequency range. 1 The selected frequency band activity can easily be observed this mode. 2 Three Fixed Edge bands can be set for each amateur frequency band covered by the transceiver in the SCOPE SET
  • Icom IC-7300 | Instruction Manual basic - Page 50
    3. Touch the signal in the zoomed area. LLInformatio ••In the Center mode, the operating frequency changes to the touched point, and the point moves to the screen center. ••In the Fixed mode, the operating frequency and marker change to the touched point. ••
  • Icom IC-7300 | Instruction Manual basic - Page 51
    supplied by Icom. User supplied. You can use an SD card of up to 2 GB, or an SDHC of up to 32 GB. Icom Icom recommends that you save the transceiver's factory default data for backup. (p. 8-7) NOTE: ••Before using the SD card, thoroughly read the card's instructions power is 15 ON,
  • Icom IC-7300 | Instruction Manual basic - Page 52
    the SD CARD set screen. 4. To close the SET screen, push EXIT several times. 5. Remove the card from the transceiver. Formatting an SD card Before using an SD card with the transceiver, be sure to format all SD cards with the built-in Format function. This creates a special folder on the
  • Icom IC-7300 | Instruction Manual basic - Page 53
    16 17 If the tuner cannot tune the antenna ••Repeat manual tuning several times. 18 ••Even if the tuner cannot tune the antenna on the first tuning, it may success at the second tuning. 19 ••Some antennas, especially for the low bands, have a narrow bandwidth. These antennas may not tune at
  • Icom IC-7300 | Instruction Manual basic - Page 54
    8 SET MODE Set mode description You can use the Set mode to set infrequently changed values or function settings. TIP: The Set mode is constructed in a tree structure. You may go to the next tree level, or go back a level, depending on the selected item. DDEntering the Set mode 1. Push MENU . ••
  • Icom IC-7300 | Instruction Manual basic - Page 55
    SET MODE 8 Tone Control SSB RX HPF/LPF (Default Sets the receive audio high-pass filter and low-pass filter cut-off frequencies in 100 Hz steps. L
  • Icom IC-7300 | Instruction Manual basic - Page 56
    Split function in the FM mode on the HF or 50 MHz band. SPLIT LOCK (Default: OFF) Turns the Split Lock function ON or OFF. [TUNER] Switch (Default: Auto) Selects whether or not to save the internal antenna tuner's status after pushing TUNER on each band. PTT Start (Default: OFF) Turns
  • Icom IC-7300 | Instruction Manual basic - Page 57
    /Manual) Selects the notch function used in the SSB or AM mode. Screen Capture [POWER] SW (Default: OFF) Assigns the Screen Capture function to POWER . 1 Screen Capture File Type 2 (Default: PNG) 3 Selects the file format for the Screen Capture function. Keyboard Type 4 (Default: Full
  • Icom IC-7300 | Instruction Manual basic - Page 58
    mode is OFF. DATA MOD (Default: ACC) Selects the connector(s) to input the modulation signal when the data mode is ON. External Keypad VOICE (Default: OFF) Enables voice memory transmission using function ON or OFF, when remotely controlling the IC-7300 through the [USB] CI-V port. LThis
  • Icom IC-7300 | Instruction Manual basic - Page 59
    the USB port. Selects the control port to be used for communication between the IC-7300 and PC, according to the operating condition. LYou mode ON or OFF. 8 MN-Q Popup (MN OFF→ON) 9 (Default: ON) Selects whether or not to display the Manual Notch filter width when you select the Manual Notch
  • Icom IC-7300 | Instruction Manual basic - Page 60
    Firmware Update Displays the Firmware Update mode. Format Formats the SD card. If you use a brand new SD card, screen. LSee section 14 of the Full Manual for details. Partial Reset Resets operating ••MY Call ••Memory Keyer ••RTTY memory ••User Band Edge ••REF Adjust ••Fixed Edges LSee "Resetting"
  • Icom IC-7300 | Instruction Manual basic - Page 61
    the problem still exists, perform a Partial reset as described to the right. If the problem still MY Call ••Memory Keyer ••RTTY memory ••User Band Edge ••REF Adjust ••Fixed Edges 11 DDAll mode. In this case, perform the All reset as described below: 20 While holding down CLEAR and V/M , push POWER
  • Icom IC-7300 | Instruction Manual basic - Page 62
    modes: USB/LSB (J3E), CW (A1A), RTTY (F1B), AM (A3E) and FM (F3E) ••Number of memory channels: 101 (including 2 scan edges) ••Antenna connector: SO-239 (antenna impedance: 50 Ω) ••Power supply Spurious emission: Harmonics Out-of-band emission ••Carrier suppression: ••
  • Icom IC-7300 | Instruction Manual basic - Page 63
    dBm (12.6 μV) (P.AMP1 ON) 4 1.8 ~ 29.999999 MHz 50 MHz and 70 MHz bands Less than -101 dBm (2.0 μV) Less than -107 dBm (1.0 μV) (P.AMP1 ON) (P.AMP2 power: More than 2.5 W (8 Ω load, 1 kHz, 10% distortion) ••AF output impedance: 8 Ω 15 ••RIT variable range: ±9.999 kHz 16 DDAntenna tuner
  • Icom IC-7300 | Instruction Manual basic - Page 64
    antenna tuner Automatic antenna tuner to tune a long wire antenna for base, portable, or mobile HF/50 MHz operation. AH-740 automatic tuning antenna High performance, automatic high-speed tuning antenna. HM-36 microphone Hand microphone with [UP]/[DOWN] switches. PS-126 dc power supply ••Output
  • Icom IC-7300 | Instruction Manual basic - Page 65
    NOTE: ••Before mounting the MB-118, carefully read 1 PRECAUTIONS (p. vii) and decide the mounting place. ••DO NOT use bolts other than the ones that are supplied 2 with the MB-118. Other bolts (longer than 8 mm/0.31 in) may damage the internal units. 3 4 5 6 7 Bolt 8 Screw Spring washer
  • Icom IC-7300 | Instruction Manual basic - Page 66
    than 3.3 kΩ 7 NC - - 8 13.8 V 13.8 V output when power is ON. Output current: Maximum 1 A 9 TKEY Not used. - 10 FSKK Controls RTTY keying. High level: Low level: Output current: More than 2.4 V Less than 0.6 V Less than 2 mA 11 MOD Modulator input. Input impedance: 10 kΩ Input level
  • Icom IC-7300 | Instruction Manual basic - Page 67
    IC-7300) q FSKK t AF q 8 V t ALC 5 w GND y SQLS w GND y - e SEND u 13.8 V e SEND u 13.8 V 6 r MOD i ALC r BAND 15 16 DDExternal keypad A circuit is used to output memory content from 4 memories. ON LThe External keypad is not supplied by Icom. (User supplied) 4.7 kø 2.2 kø 1.5 kø
  • Icom IC-7300 | Instruction Manual basic - Page 68
    transmits. (RCA Plug) This terminal is used to control an external non-Icom linear amplifier. T/R control voltage and power socket Accepts the regulated DC power for 13.8 V DC ±15% through the supplied DC power cable. RWARNING! NEVER reverse the DC power cable polarity. Rear panel view IC-7300
  • Icom IC-7300 | Instruction Manual basic - Page 69
    12-3 All reset 9-1 Antenna tuner 10-2 Auto tuning 7-1 Connecting 2-3 Manual tuning 7-1 Operation 7-1 PTT tuner 7-1 ANTI VOX 4-7 Attenuator 4-1 Audio scope screen 5-3 Auto Notch function 4-6 Auto Tuning Step function 3-4 B Band Edge Beep 3-5 Entering 3-6 Band operation, 5 MHz frequency
  • Icom IC-7300 | Instruction Manual basic - Page 70
    -2 Operating band, selecting 3-2 Operating mode, selecting 3-2 Options 11-1 Others (Set mode 8-7 P Panel description 1-1 Partial reset 9-1 PHONES jack 12-3 Power ON or OFF 3-1 When first applying 3-1 Preamplifiers 4-1 PTT Tuner start 7-1 Q QUICK MENU 1-6 Quick Split function, using
  • Icom IC-7300 | Instruction Manual basic - Page 71
    today. Exposed persons are assumed to be beneath the antenna array and have a typical height of 1.8 m. The figures assume the worst case emission of a constant carrier. For the bands 10 MHz and higher the following power density limits have been recommended: 10-50 MHz 2 W/sq m Vertical clearance
  • Icom IC-7300 | Instruction Manual basic - Page 72
    MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR IC-7300 #05 (Italy) < Intended Country of Use > AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT of Use > AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR A-7292H-1EX Printed in Japan © 2016 Icom Inc
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
BASIC MANUAL
i7300
HF/50 MHz TRANSCEIVER