Intel DG965WH Product Specification - Page 58

Table 30. States for a Two-Color Power LED

Get Intel DG965WH PDF manuals and user guides View all Intel DG965WH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Intel Desktop Board DG965WH Technical Product Specification 2.8.2.3.2 Reset Switch Header Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST. 2.8.2.3.3 Power/Sleep LED Header Pins 2 and 4 can be connected to a one- or two-color LED. Table 29 shows the possible states for a one-color LED. Table 30 shows the possible states for a two-color LED. Table 29. States for a One-Color Power LED LED State Description Off Power off/sleeping Steady Green Running Table 30. States for a Two-Color Power LED LED State Description Off Steady Green Steady Yellow Power off Running Sleeping NOTE The colors listed in Table 29 and Table 30 are suggested colors only. Actual LED colors are product- or customer-specific. 2.8.2.3.4 Power Switch Header Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Intel Desktop Board DG965WH Technical Product Specification
58
2.8.2.3.2
Reset Switch Header
Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type
switch that is normally open.
When the switch is closed, the board resets and runs the
POST.
2.8.2.3.3
Power/Sleep LED Header
Pins 2 and 4 can be connected to a one- or two-color LED.
Table 29 shows the
possible states for a one-color LED.
Table 30 shows the possible states for a two-color
LED.
Table 29. States for a One-Color Power LED
LED State
Description
Off
Power off/sleeping
Steady Green
Running
Table 30. States for a Two-Color Power LED
LED State
Description
Off
Power off
Steady Green
Running
Steady Yellow
Sleeping
±
NOTE
The colors listed in Table 29 and Table 30 are suggested colors only.
Actual LED
colors are product- or customer-specific.
2.8.2.3.4
Power Switch Header
Pins 6 and 8 can be connected to a front panel momentary-contact power switch.
The
switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power
supply to switch on or off.
(The time requirement is due to internal debounce circuitry
on the board.)
At least two seconds must pass before the power supply will recognize
another on/off signal.