Invacare TDXSR-CG-HD Owners Manual - Page 88

After installing front shroud, ensure that the mounting screws on the front shroud/battery retention

Get Invacare TDXSR-CG-HD PDF manuals and user guides View all Invacare TDXSR-CG-HD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

7 SETUP/MAINTENANCE Installing the Front Shroud/Battery Retention Bracket and Rear Shroud ƽ CAUTION Wheelchairs with TRRO or TRBKTS Only - Battery retention brackets MUST be installed at all times. Otherwise, the wheelchair will not be WC/19 compliant. After installing front shroud, ensure that the mounting screws on the front shroud/battery retention bracket are fully engaged into the battery box.  For this procedure, refer to FIGURE 1 on page 84. 1. Reinstall the front shroud/battery retention bracket onto front of wheelchair frame. 2. Install two mounting screws on the sides of the front shroud/battery retention bracket. ƽ CAUTION When installing batteries, ensure battery connector is securely engaged to the controller connector - otherwise serious personal injury may result. 3. Wheelchairs with Footboards Only: Using the mounting screw and washer, secure the footboard support to the wheelchair frame. 4. Connect the controller to the batteries at the rear of the wheelchair. 5. Reinstall the rear shroud and secure in place with three mounting screws.  New Batteries MUST be fully charged before using, otherwise the life of the battery(ies) will be reduced. 6. If necessary, charge the batteries. Refer to Charging Batteries on page 56. Invacare® TDX®SP, TDX SR 88 Part No 1143190

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
7
SETUP/MAINTENANCE
Invacare® TDX®SP, TDX SR
88
Part No 1143190
Installing the Front Shroud/Battery Retention Bracket and Rear Shroud
1.
Reinstall the front shroud/battery retention bracket onto front of wheelchair frame.
2.
Install two mounting screws on the sides of the front shroud/battery retention bracket
.
3.
Wheelchairs with Footboards Only: Using the mounting screw and washer, secure the footboard support to the wheelchair frame.
4.
Connect the controller to the batteries at the rear of the wheelchair.
5.
Reinstall the rear shroud and secure in place with three mounting screws.
6.
If necessary, charge the batteries. Refer to Charging Batteries
on page 56.
±
CAUTION
Wheelchairs with TRRO or TRBKTS Only - Battery retention brackets MUST be installed at all times. Otherwise, the
wheelchair will not be WC/19 compliant.
After installing front shroud, ensure that the mounting screws on the front shroud/battery retention bracket are fully
engaged into the battery box.
For this procedure, refer to FIGURE 1 on page 84.
±
CAUTION
When installing batteries, ensure battery connector is securely engaged to the controller connector - otherwise serious
personal injury may result.
New Batteries MUST be fully charged before using, otherwise the life of the battery(ies) will be reduced.