JVC GZ-MG20 Instruction Manual - Page 16

Data Battery System, Using AC Power, About Batteries - problems

Get JVC GZ-MG20 - Everio Camcorder - 25 x Optical Zoom PDF manuals and user guides View all JVC GZ-MG20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

16 EN GETTING STARTED Data Battery System You can check the remaining battery power and the recordable time. 1 Make sure the battery is attached. 2 Open the LCD monitor fully. 3 Press INFO/ repeatedly, and the battery status screen appears. ● It is displayed for approx. 3 seconds if the button is pressed and released quickly, and for approx. 15 seconds if the button is pressed and held for several seconds. ● If "COMMUNICATING ERROR" appears instead of the battery status even though you tried to press INFO/ several times, there may be a problem with your battery. In such a case, consult your nearest JVC dealer. ● The recordable time display should only be used as a guide. It is displayed in 10 minute units. Using AC Power Perform step 4 in "Charging the Battery Pack". NOTE: The provided AC adapter features automatic voltage selection in the AC range from 110 V to 240 V. About Batteries DANGER! Do not attempt to take the batteries apart, or expose them to flame or excessive heat, as it may cause a fire or explosion. WARNING! Do not allow the battery or its terminals to come in contact with metals, as this can result in a short circuit and possibly start a fire. To resume the original function of the accurate battery power indication If the battery power indication differs from the actual operating time, fully charge the battery, and then run it down. However this function may not turn back if the battery was used for a long period of time under extremely high/low temperature condition or charged too many times.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
16
EN
GETTING STARTED
Data Battery System
You can check the remaining battery power and
the recordable time.
1
Make sure the battery is attached.
2
Open the LCD monitor fully.
3
Press
INFO
/
repeatedly, and the battery
status screen appears.
●
It is displayed for approx. 3 seconds if the
button is pressed and released quickly, and for
approx. 15 seconds if the button is pressed
and held for several seconds.
●
If “COMMUNICATING ERROR” appears
instead of the battery status even though you
tried to press
INFO
/
several times, there
may be a problem with your battery. In such a
case, consult your nearest JVC dealer.
●
The recordable time display should only be
used as a guide. It is displayed in 10 minute
units.
Using AC Power
Perform step
4
in “Charging the Battery Pack”.
NOTE:
The provided AC adapter features automatic voltage
selection in the AC range from 110 V to 240 V.
About Batteries
DANGER!
Do not attempt to take the batteries
apart, or expose them to flame or excessive
heat, as it may cause a fire or explosion.
WARNING!
Do not allow the battery or its
terminals to come in contact with metals, as this
can result in a short circuit and possibly start a
fire.
To resume the original function of the
accurate battery power indication
If the battery power indication differs from the
actual operating time, fully charge the battery,
and then run it down. However this function may
not turn back if the battery was used for a long
period of time under extremely high/low
temperature condition or charged too many
times.