Kenwood DDX9705S User Manual - Page 90

Installing the unit, Installation procedure, Non-Japanese cars, Except DDX9705S

Get Kenwood DDX9705S PDF manuals and user guides View all Kenwood DDX9705S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Connection/Installation ÑÑInstallation procedure 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Make the proper input and output wire connections for each unit. 3) Connect the speaker wires of the wiring harness. 4) Connect the wiring harness wires in the following order; ground, battery, ignition. 5) Connect the wiring harness connector to the unit. 6) Install the unit in your car. 7) Reconnect the ¤ terminal of the battery. 8) Perform the Initial Setup. See Initial setup (P.7). Installing the unit ÑÑNon-Japanese cars (Except DDX9705S) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ÑÑJapanese cars 6 or 7 Car Bracket 6 or 7 NOTE • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). ÑÑTrim plate (Except DDX9705S) 1) Attach accessory 8 to the unit. 8 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Connection/Installation
90
Ñ
Installation procedure
1) To prevent a short circuit, remove the key
from the ignition and disconnect the
¤
terminal of the battery.
2) Make the proper input and output wire
connections for each unit.
3) Connect the speaker wires of the wiring
harness.
4) Connect the wiring harness wires in the
following order; ground, battery, ignition.
5) Connect the wiring harness connector to the
unit.
6) Install the unit in your car.
7) Reconnect the
¤
terminal of the battery.
8) Perform the Initial Setup.
See
Initial setup (P.7)
.
Installing the unit
Ñ
Non-Japanese cars
(Except DDX9705S)
Bend the tabs of the
mounting sleeve
with a screwdriver
or similar utensil and
attach it in place.
Ñ
Japanese cars
6
or
7
6
or
7
Car Bracket
NOTE
• Make sure that the unit is installed securely in
place. If the unit is unstable, it may malfunction
(eg, the sound may skip).
Ñ
Trim plate (Except DDX9705S)
1) Attach accessory
8
to the unit.
8