Kenwood TH-D74A User Manual - Page 76

SETTING SmartBeaconingTM, Operation When Receiving a QSY, Low Speed/ High Speed, Slow Rate, Fast Rate

Get Kenwood TH-D74A PDF manuals and user guides View all Kenwood TH-D74A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Operation When Receiving a QSY When QSY (frequency) information is received, the station list appears with the verified frequency. 1 Select [Tune], and press [A/B]. Slow Rate Low speed transmission interval time. 1 Access Menu No. 531. • The frequency is set in the voice channel (non-data band). Note: ◆◆ When using 6.5 kHz or 12.5 kHz step values, the display does not indicate values for 100 Hz and lower. ◆◆ If D-STAR repeater information is included in the QSY information of the received beacons and when the voice channel (non-data band) is in DR mode, the QSY function will be activated even outside the range of distance limit. Gateway communication will be configured automatically. 2 Select from [1] to [100] minutes. Fast Rate High speed transmission interval time . 1 Access Menu No. 532. SETTING SmartBeaconingTM Set to use "SmartBeaconing" (Menu No. 510) with APRS data transmission. This function optimizes beacon transmission based on driving direction and speed. Use this function when you want to track your transmissions, especially for optimizing crossover beacon transmission intervals. When using smart beaconing, set Menu No. 571 (TX Beep) to [On] (default value) to confirm the transmission status of the beacon. < SmartBeaconing™ from HamHUD Nichetronix > 2 Select from [10] to [180] seconds. Turn Angle Driving direction change, minimum value setting. 1 Access Menu No. 533. Low Speed/ High Speed 1 Access Menu No. 530. 2 Select from [5] to [90] degrees. 2 Select the Low speed and High speed. • Low speed setting (2 ~ 30 ). When the speed is lower than this, beacons are transmitted at the time interval specified under "Slow Rate". • High speed setting (2 ~ 90 ). When the speed is faster than this, beacons are transmitted at the time interval specified under "Fast Rate". Note: ◆◆ To select the speed setting of the units, access Menu No. 970 (Speed, Distance). Turn Slope Driving direction change, additional value setting. 1 Access Menu No. 534. 2 Select from [1] to [255] (10degrees/speed). 14-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
14-17
Operation When Receiving a QSY
When QSY (frequency) information is received, the station list
appears with the verified frequency.
1
Select
[Tune], and press
[A/B]
.
•
The frequency is set in the voice channel (non-data
band).
Note:
◆
When using 6.5 kHz or 12.5 kHz step values, the display does
not indicate values for 100 Hz and lower.
◆
If D-STAR repeater information is included in the QSY
information of the received beacons and when the voice
channel (non-data band) is in DR mode, the QSY function will
be activated even outside the range of distance limit. Gateway
communication will be configured automatically.
SETTING SmartBeaconing
TM
Set to use “SmartBeaconing” (Menu No. 510) with APRS data
transmission.
This function optimizes beacon transmission based on driving
direction and speed.
Use this function when you want to
track your transmissions, especially for optimizing crossover
beacon transmission intervals.
When using smart beaconing, set Menu No. 571 (TX Beep)
to [On] (default value) to confirm the transmission status of
the beacon.
< SmartBeaconing™ from HamHUD Nichetronix >
Low Speed/ High Speed
1
Access Menu No. 530.
2
Select the Low speed and High speed.
•
Low speed setting (2 ~ 30 <mi/h, km/h or knots>). When
the speed is lower than this, beacons are transmitted at
the time interval specified under “Slow Rate”.
•
High speed setting (2 ~ 90 <mi/h, km/h or knots>).
When the speed is faster than this, beacons are
transmitted at the time interval specified under “Fast
Rate”.
Note:
◆
To select the speed setting of the units, access Menu No.970
(Speed, Distance).
Slow Rate
Low speed transmission interval time.
1
Access Menu No. 531.
2
Select from [1] to [100] minutes.
Fast Rate
High speed transmission interval time .
1
Access Menu No. 532.
2
Select from [10] to [180] seconds.
Turn Angle
Driving direction change, minimum value setting.
1
Access Menu No. 533.
2
Select from [5] to [90] degrees.
Turn Slope
Driving direction change, additional value setting.
1
Access Menu No. 534.
2
Select from [1] to [255] (10degrees/speed).