Kenwood TS-2000 Operation Manual - Page 19

16 PF F LOCK A ATT LEVEL VOX PRE LEVEL PROC SEND ANT1/2 AT PHONES LEVEL LEVEL MIC MANUAL N.R. LO/ WIDTH B.C. A.N. 1 2 3 CH1/REC CH2/REC CH3/REC 4 5 6 TONE/SEL METER CTCSS/SEL 7 8 9 NB/LEVEL AGC/OFF FINE/STEP . 0 DCS/SEL SHIFT/OFFSET ENT HI/ SHIFT FUNC MAIN CAR MIC TX MONI PWR DELAY KEY AUTO LSB USB REV CW FSK NAR FM AM CLR DISP SEL 1MHz 14 15 18 17 4 GETTING ACQUAINTED HF/VHF/UHF ALL MODE MULTI BANDER TS-2000 CW TUNE RIT ALT XIT 9.6k STA CON RIT/SUB SUB MENU TFSET _ CLEAR P.C.T SET QUICK MEMO MANUAL BC MAIN RF GAIN MR M.IN + MULTI CH C.IN CALL MAIN SUB CTRL SG.SEL SCAN SATL M/S REV A/B SPLIT VFO/CH TRACE VFO/M A=B MG.SEL M VFO M.IN MAIN AF SUB SQL !4 Multi-purpose keypad Consists of 10 keys that are used to enter numeric data. Also used for the following functions: • 1/ CH1/REC, 2/ CH2/REC, and 3/ CH3/REC keys Press to play back or record the CW or voice messages that are associated with the DRU-3A Digital Recording Unit {page 89} and the internal electronic keyer {page 43}. • 4/ TONE/SEL key Press to activate the sub-audible Tone function to access repeaters for FM mode. To select the Tone frequency, press [FUNC], [4/ TONE/SEL], then select your desired tone frequency using the MULTI/ CH control {page 33}. • 5/ METER key Press to select the meter scales {page 19}. • 6/ CTCSS/SEL key Press to activate the Continuous Tone Coded Squelch System (CTCSS) function for FM mode. To select the CTCSS tone frequency, press [FUNC], [5/ CTCSS/SEL], then select your desired CTCSS tone frequency using the MULTI/ CH control {page 35}. • 7/ NB/LEVEL key Press to switch the Noise Blanker ON or OFF. Press [FUNC], [7/ NB/LEVEL] to adjust the Noise Blanker level {page 57}. • 8/ AGC/OFF key Press to adjust the response time of the Automatic Gain Control. To switch the AGC OFF, press [FUNC], [8/ AGC/OFF] {page 38}. • 9/ FINE/STEP key Press to activate the Fine tuning function to allow more precise tuning {page 38}. • •/ DCS/SEL key Press to activate the Digital Coded Squelch function for FM mode. To select the DCS code, press [FUNC], [•/ DCS/SEL], then select your desired code using the MULTI/ CH control {page 36}. • 0/ SHIFT/OFFSET key Press to switch the Shift function for FM mode ON or OFF when accessing the repeaters. The Shift frequency can be manually adjusted by pressing [FUNC], [0/ SHIFT/OFFSET], then adjusting the shift frequency value using the MULTI/ CH control {page 32}. • ENT key Press to enter your desired frequency using the keypad {page 37}. !5 FUNC key Press to access the secondary functions that are assigned to the keys. While FUNC is active, the FUNC LED lights orange. !6 MIC/ CAR key Press to adjust the microphone gain {page 20}. While the Speech Processor function is ON, it becomes the Speech Processor output level adjustment key {page 40}. Press [FUNC], [MIC/ CAR] to adjust the carrier level for CW, FSK and AM mode {page 20}. !7 PWR/ TX MONI key Press to adjust the output power {page 20}. Press [FUNC], [PWR/ TX MONI] to monitor your transmission signal {page 79}. !8 KEY/ DELAY key Press to adjust the internal electronic keyer speed. Press [FUNC], [KEY/ DELAY] to adjust the VOX delay time or break-in time (Full break-in/ Semi break-in time) for CW mode {page 42}. 9