Kodak DP1100 Reference Manual - Page 27

Turning Off the Projector

Get Kodak DP1100 - Digital Projector PDF manuals and user guides View all Kodak DP1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Setting up the Projector Turning Off the Projector If you want to turn off the projector for a short period of time, press the button on the keypad or remote. This blanks the screen for fifteen minutes, but keeps the projector running. (You can change the amount of time the projector stays in standby mode; see "Standby Time" on page 38 for details.) After 15 minutes, the lamp goes out (the projector keeps running). To exit standby mode, press the button again. (It may take several seconds for the projection lamp to reach full power and project the image again.) To completely power off the projector, press the "O" side of the power switch on the side of the projector. If you want to turn the projector back on immediately, you must allow about a minute for the lamp to cool. The lamp won't light if it's too hot. &DXWLRQ :KHQ \RX GLVFRQQHFW WKH SURMHFWRU DIWHU \RX KDYH VZLWFKHG LW RII DOZD\V UHPRYH WKH SRZHU FRUG IURP WKH HOHFWULFDO RXWOHW ILUVW WKHQ UHPRYH LW IURP WKH SURMHFWRU 3/99 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Setting up the Projector
3/99
23
Turning Off the Projector
If you want to turn off the projector for a short period of time,
press the
button on the keypad or remote. This blanks the
screen for fifteen minutes, but keeps the projector running. (You
can change the amount of time the projector stays in standby
mode; see “Standby Time” on page 38 for details.) After 15
minutes, the lamp goes out (the projector keeps running). To exit
standby mode, press the
button again. (It may take several
seconds for the projection lamp to reach full power and project
the image again.)
To completely power off the projector, press the “O” side of the
power switch on the side of the projector. If you want to turn the
projector back on immediately, you must allow about a minute for
the lamp to cool. The lamp won’t light if it’s too hot.
&DXWLRQ± :KHQ²\RX²GLVFRQQHFW²WKH²SURMHFWRU²DIWHU²\RX²KDYH²
VZLWFKHG²LW²RII³²DOZD\V²UHPRYH²WKH²SRZHU²FRUG²IURP²
WKH²HOHFWULFDO²RXWOHW²ILUVW³²WKHQ²UHPRYH²LW²IURP²WKH²
SURMHFWRU´