Konica Minolta bizhub 4752 bizhub 4752/4052 Quick Start Guide - Page 88

bizhub 4752/4052

6-21

6.6

Registering a destination

6

Basic Usage

Chapter 6

The registered content of [E-Mail]

The registered content of [PC (SMB)]

[Line Settings]

If necessary, specify how to send a fax to a destination you want to register.

You may change the settings you made here before sending a fax.

•

[Overseas TX]: Used to send a fax to areas where communication condi-

tions are poor. Faxes are sent at a lower speed.

•

[ECM OFF]: ECM is an error correction mode defined by ITU-T (Internation-

al Telecommunication Union - Telecommunication Standardization Sec-

tor). Fax machines equipped with the ECM feature communicate with each

other, confirming that the sent data is free of errors. This prevents image

blurring caused by telephone line noise.

The communication time can be reduced by setting ECM to OFF for trans-

mission. However, an image error or communication error may occur de-

pending on the specified communication time value, so change the value

to suit conditions.

•

[V34 OFF]: V.34 is a communication mode used for super G3 fax commu-

nication. When the remote machine or this machine is connected to a tele-

phone line via PBX, however, you may not establish a communication in the

super G3 mode depending on telephone line conditions. In this case, it is

recommended that you turn the V.34 mode off to send data.

•

[Check Dest. & Send]: When using the Check Dest. And Send function, se-

lect [Yes]. The fax number specified for fax is checked against the destina-

tion fax number (CSI) and the fax is sent only when they match.

Settings

Description

[E-Mail Address]

Enter the E-mail address as a destination.

If prefixes and suffixes are registered, you can recall a registered domain name

etc. to complement entry.

Settings

Description

[User ID]

Enter the name of a user who has privileges to access the folder specified in

[File Path] (using up to 64 characters).

•

For workgroup user, only type in only the user name. Entry example: "Us-

er01"

•

For domain user, type in user-name@domain-name. Entry example: "Us-

[email protected]"

[Password]

Enter the password of the user specified in [User ID].

[Host Address]

Enters the destination computer name (host name) or IP address (using up to

253 bytes).

•

Example of computer name (host name) entry: "HOME-PC"

•

Example of IP address (IPv4) entry: "192.168.1.1"

•

Example of IP address (IPv6) entry: "fe80::220:6bff:fe10:2f16"

[Check Connection]

Check whether or not the host name you entered in [Host Address] exists.

[File Path]

Enter the shared folder name of the computer specified in [Host Address] (us-

ing up to 255 bytes). The shared folder name is generally referred to as a share

name.

•

Entry example: "scan"

When specifying a folder in the shared folder, insert a symbol, "\", between

folder names.

•

Entry example: "scan\document"

[Host Name Search]

Searches for the host name to be applied to [Host Address]. To search for the

host name, specify a group name.

•

[Group Name]: Displays the name of the group to which the user belongs

by default. To change the group name, tap [Change], then enter the group

name (using up to 15 characters). After entering the group name, specify

search conditions, then tap [Search].

•

[Host Name]: Enter the target host name (using up to 15 characters). After

entering the host name, specify search conditions, then tap [Search].

Settings

Description

Section	Page
Table of contents	2
1 Introduction	7
1.1 Introduction	7
Environmental initiatives	7
ENERGY STAR®	7
What is an ENERGY STAR® Product?	8
Environmental benefits of power management	8
Recycled Paper	8
Duplex printing	8
1.2 Safety information	9
Warning and precaution symbols	9
These are some of major exemplary graphical symbols.	9
<Power source connection>	10
<Installation>	11
<Using the product>	12
<Consumables>	14
1.3 Regulation notices	16
CE Marking (Declaration of Conformity) for users of the European Union (EU)	16
FCC Part 15 - Radio Frequency Devices	16
INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 5) (for Canada users)	17
Electromagnetic Interference	17
GS Certification	17
Laser Safety	17
Internal Laser Radiation	18
CDRH regulations	18
For European users	18
Laser safety label	18
Ozone Release	19
Changing replaceable lithium batteries used in products	19
Acoustic noise (for European users only)	19
Notification for California Customers	19
Recycling batteries (for Taiwan users only)	19
For EU member states only	19
USB Host	20
Graphic symbols used on this machine	20
1.4 Caution notations and labels	21
1.5 Special Notice to User	22
For Canada	22
For U.S.A.	22
For Europe	23
1.6 Space requirements	24
1.7 Operation precautions	25
Power source	25
Operating environment	25
Storage of copies	25
Data stored in this machine	25
Precautions for Carrying the Machine	26
1.8 Legal restrictions on reproduction	27
1.9 Trademark acknowledgements	28
Copyright	29
Note	29
1.10 Software End User License Agreement	30
2 User's Guides	33
2.1 Intended use of office MFP devices	33
Intended use	33
Impermissible operating conditions	33
Exclusion of liability	33
2.2 Introduction to user's guide	34
2.2.1 User's Guide CD	34
Layout of top page	35
Operating environment	35
Viewing the top page	35
2.2.2 Target groups	36
2.2.3 Symbols and notations used in this manual	36
Procedural instruction	36
Symbols and notations	37
Names and notations of applications	37
3 Overview of This Machine	39
3.1 About this machine	39
3.1.1 Name of parts	39
Front	39
Side/rear	40
3.1.2 Option configuration	41
List of optional components	41
List of other optional components	42
3.2 Power Supply	43
3.2.1 Power Switch and Power key locations	43
3.2.2 Turning the Power Switch ON or OFF	44
3.2.3 Using the Power key	44
When using the Power key as a Power Save key	45
When using the Power key as a Sub Power Off key	45
3.3 Control Panel	46
3.4 Operating the Touch Panel	48
Tap	48
Double-tap	48
Flick	48
Drag	49
Pan	49
Long-tap	49
Drag & Drop	50
Pinch-in / Pinch-out	50
Rotation	51
Displaying the Keypad	51
Moving the Keypad	51
Switching to the entry or selection screen	52
Precautions on using the Touch Panel	52
3.5 Main Menu	53
3.6 Entering characters	55
4 Loading Paper	57
4.1 Paper	57
4.1.1 Confirm the available paper types	57
4.1.2 Confirm the available paper sizes	58
4.1.3 Precautions for Correct Operations	58
Unavailable paper	58
Storing paper	59
4.2 Loading Paper in Bypass Tray	60
How to load paper into the Bypass Tray	60
4.3 Loading paper into Tray 1	62
5 Initial Settings of This Machine	65
5.1 Preparation for network connection (for administrators)	65
Checking a LAN cable for connection	65
Assigning an IP address	65
5.2 Preparation for fax (for administrators)	66
Checking the modular cable connection	66
Specifying the type of telephone line	66
Making preparations for using the machine in a Private Branch Exchange (PBX) environment	66
Selecting a receiving method	66
Registering the sender information	66
Set the date and time for the machine	66
5.3 Security settings (for administrators)	67
5.3.1 Hard Disk setting	67
5.3.2 Configuring [Quick Security Setting]	67
5.4 Administrator Password	67
6 Basic Usage	69
6.1 Using the print function (Windows environment)	69
6.1.1 Printer driver	69
6.1.2 Preparation for printing (network connection)	69
Checking the LAN cable connection	69
Checking the network settings	69
Installing the printer driver	70
6.1.3 Preparation for printing (USB connection)	71
Changing the installation settings (Windows 7/8.1/10/Server 2008 R2/Server 2012/Server 2012 R2/Server 2016)	71
Installing the printer driver	72
6.1.4 Initial settings of the printer driver	73
6.1.5 How to print	74
6.2 Using the scan function	75
6.2.1 Available operations in the scan function	75
6.2.2 How to send	75
6.3 Using the fax function	77
6.3.1 Fax function	77
6.3.2 How To Send	77
6.3.3 Introduction of fax transmission function	79
6.3.4 Introduction of fax receiving function	80
6.3.5 Introduction of internet fax function	80
6.3.6 Introduction of IP address fax function	80
6.4 Using the copy function	81
6.4.1 How to copy	81
6.4.2 Introduction of copy function	82
6.5 Printing a file stored on USB memory	85
Supported USB memory devices	85
How to print	85
6.6 Registering a destination	87
6.6.1 Address book	87
6.6.2 Registering address books	87
Registering from the Utility	87
Registering from Address Book	91
Registering from the Fax/Scan basic screen	91

Konica Minolta bizhub 4752 bizhub 4752/4052 Quick Start Guide - Page 88

Check Dest. & Send]: When using the Check Dest. And Send function, se

Page 88 highlights