Konica Minolta bizhub C3110 bizhub C3110 Description of Utility Keys - Page 38

Line Param Setting] - service mode

Page 38 highlights

6.6 [Fax Settings] 6 [Line Param Setting] To display: [UTILITY] - [Admin Settings] - [Fax Settings] - [Line Param Setting] Configure the environment to use fax functions on this machine, such as the types of telephone lines (dialing method) and fax receive mode. Settings [Dialing Method] [RX MODE] [Ring Pattern] [Number of RX Rings] [Number of Redials] [Redial Interval] [Line Monitor] [Line Mon Vol - TX] [Line Mon Vol - RX] [Manual RX V.34 OFF] Description Select the line type according to your environment. The default value depends on the region the machine is used in. Select a receive mode. • [AUTO RX]: Automatically start receiving a fax if the call is a fax call. • [MANUAL RX]: Manually request the reception of a fax. Select this option when this machine is used with a telephone connected to it, which is frequently used, and if you always prefer to receive faxes manually. [AUTO RX] is specified by default. Select a fax ring pattern when the DRPD (Distinctive Ring Pattern Detection) service is used. When this machine receives a call signal of the selected pattern, fax receiving starts automatically. [Normal Ring] is specified by default. Note In general use, set this to [Normal Ring]. If DRPD is set by mistake in a region where DRPD cannot be used, it will result in a fax receiving failure. If necessary, change the number of times the phone rings before automatically receiving a fax. The default value depends on the region the machine is used in. If the machine fails to send a fax successfully, it automatically redials the same destination after a certain period of time has elapsed. If necessary, change the number of redials. The default value depends on the region the machine is used in. If necessary, change the redial intervals when you specified a value in [Number of Redials]. [3 min.] is specified by default. Select whether or not to play sounds on the telephone line from speakers during fax communication. [OFF] is specified by default. Monitors sounds output from the machine. Specify the monitor sound volume between 0 and 8. This function is available only when [Line Monitor] is set to [Until CX Complete] or [Until TX Complete]. [3] is specified by default. Note When communicating with fax, monitoring sound is generated even if send or receive monitoring sound of this machine is set to [0] since the sound is generated both on this machine and on the destination side. For setting to mute, set both [Line Mon Vol - TX] and [Line Mon Vol - RX] to [0], or set [Line Monitor] to [OFF]. Monitors sounds output from the recipient, including switching equipment or TA. Specify the monitor sound volume between 0 and 8. This function is available only when [Line Monitor] is set to [Until CX Complete] or [Until TX Complete]. [4] is specified by default. Note When communicating with fax, monitoring sound is generated even if send or receive monitoring sound of this machine is set to [0] since the sound is generated both on this machine and on the destination side. For setting to mute, set both [Line Mon Vol - TX] and [Line Mon Vol - RX] to [0], or set [Line Monitor] to [OFF]. Select whether or not to automatically release the V.34 mode when manually receiving a fax (G3). [ENABLE] is specified by default. [Description of Utility Keys] 6-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49

[Description of Utility Keys]
6-18
6.6
[Fax Settings]
6
[Line Param Setting]
To display: [UTILITY] - [Admin Settings] - [Fax Settings] - [Line Param Setting]
Configure the environment to use fax functions on this machine, such as the types of telephone lines (dialing
method) and fax receive mode.
Settings
Description
[Dialing Method]
Select the line type according to your environment.
The default value depends on the region the machine is used in.
[RX MODE]
Select a receive mode.
[AUTO RX]: Automatically start receiving a fax if the call is a fax call.
[MANUAL RX]: Manually request the reception of a fax. Select this option
when this machine is used with a telephone connected to it, which is fre-
quently used, and if you always prefer to receive faxes manually.
[AUTO RX] is specified by default.
[Ring Pattern]
Select a fax ring pattern when the DRPD (Distinctive Ring Pattern Detection)
service is used.
When this machine receives a call signal of the selected pattern, fax receiving
starts automatically.
[Normal Ring] is specified by default.
Note
In general use, set this to [Normal Ring]. If DRPD is set by mistake in a region
where DRPD cannot be used, it will result in a fax receiving failure.
[Number of RX Rings]
If necessary, change the number of times the phone rings before automatically
receiving a fax.
The default value depends on the region the machine is used in.
[Number of Redials]
If the machine fails to send a fax successfully, it automatically redials the same
destination after a certain period of time has elapsed. If necessary, change the
number of redials.
The default value depends on the region the machine is used in.
[Redial Interval]
If necessary, change the redial intervals when you specified a value in [Number
of Redials].
[3 min.] is specified by default.
[Line Monitor]
Select whether or not to play sounds on the telephone line from speakers dur-
ing fax communication.
[OFF] is specified by default.
[Line Mon Vol - TX]
Monitors sounds output from the machine. Specify the monitor sound volume
between 0 and 8.
This function is available only when [Line Monitor] is set to [Until CX Complete]
or [Until TX Complete].
[3] is specified by default.
Note
When communicating with fax, monitoring sound is generated even if send or
receive monitoring sound of this machine is set to [0] since the sound is gen-
erated both on this machine and on the destination side. For setting to mute,
set both [Line Mon Vol - TX] and [Line Mon Vol - RX] to [0], or set [Line Monitor]
to [OFF].
[Line Mon Vol - RX]
Monitors sounds output from the recipient, including switching equipment or
TA. Specify the monitor sound volume between 0 and 8.
This function is available only when [Line Monitor] is set to [Until CX Complete]
or [Until TX Complete].
[4] is specified by default.
Note
When communicating with fax, monitoring sound is generated even if send or
receive monitoring sound of this machine is set to [0] since the sound is gen-
erated both on this machine and on the destination side. For setting to mute,
set both [Line Mon Vol - TX] and [Line Mon Vol - RX] to [0], or set [Line Monitor]
to [OFF].
[Manual RX V.34 OFF]
Select whether or not to automatically release the V.34 mode when manually
receiving a fax (G3).
[ENABLE] is specified by default.