LG 32LT340C INSTALLATION - Page 25

HCEC Setup, Receive Only

Get LG 32LT340C PDF manuals and user guides View all LG 32LT340C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

25 HCEC Setup ENGLISH 1 Go to General → HCEC Setup. (1) HCEC Setup ••When HCEC Setup is set to CEC Mode, You can adjust IR Decoding, Device ID, StandBy menu and SIMPLINK feature automatically changed to the on state, and the user can not change this status. (a) IR Decoding ••When CEC Mode is set to HCEC Mode, the TV decodes and changes it into a CEC Message and sends it to Command via the HDMI CEC Line. The default value is Disable. (b) Device ID ••Sets the ID of a device(Logical Address) connected to the CEC Line. You can choose between All and E. ••The default value is All. (c) Stand By ••Sets the sending and receiving scenario of the operation about [CEC Op standBy(0x0c) Command(Device Power)]. ••The detailed scenario is described on the table below. Send Only Receive Only All Off Send O X O X Receive X O O X (2) HTNG HotelMode ••If the following options are selected because of the HTNG command: * Power On Default, Start Volume, Maximum Volume, Minimum Volume, then the value for the HTNG HotelMode changes automatically to Enable and, even if the HotelMode is set to Disable, the above options are still affected. ••If you change it to Disable, then the values set by the HTNG will be canceled.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
HCEC Setup
1
Go to
General
→
HCEC Setup
.
(1) HCEC Setup
•
When
HCEC Setup
is set to
CEC Mode
, You can adjust
IR Decoding
,
Device ID
,
StandBy
menu and
SIMPLINK feature automatically changed to the on state, and the user can not change this status.
(a) IR Decoding
•
When
CEC Mode
is set to
HCEC Mode
, the TV decodes and changes it into a CEC Message and sends
it to Command via the HDMI CEC Line. The default value is
Disable
.
(b) Device ID
•
Sets the ID of a device(Logical Address) connected to the CEC Line. You can choose between
All
and
E
.
•
The default value is
All
.
(c) Stand By
•
Sets the sending and receiving scenario of the operation about [CEC Op standBy(0x0c)
Command(Device Power)].
•
The detailed scenario is described on the table below.
Send
Receive
Send Only
O
X
Receive Only
X
O
All
O
O
Off
X
X
(2) HTNG HotelMode
•
If the following options are selected because of the HTNG command:
* Power On Default,
Start Volume
,
Maximum Volume
,
Minimum Volume
, then the value for the
HTNG
HotelMode
changes automatically to
Enable
and, even if the HotelMode is set to
Disable
, the above
options are still affected.
•
If you change it to
Disable
, then the values set by the HTNG will be canceled.
25
ENGLISH