LG 42PC5DC Owners Manual - Page 113

12.OSDSelec(tCommankdI): ToselecOtSD(OnScreeDnisplaoyn) /off. TransmisSiOn [k] [I] [ ] [Set ID][] [Data] [Cr] Data 00: OSD off Data 01 : OSD on ACknowledgemen_ [i] [ ][Set ID] [ ] [OK/NG] [Data] [x] 1 3. Remote Control Lock Mode (Command: k m) To lock the remote control and the front panel controls on the TV. TransmissiOn[k] [m] [] [Set ID] [] [Data] [Cr] Data 00: Lock off Data 01 : Lock on Acknowledgement[m][] [Set ID] [ ] [OKiNG] [Data] [x] If you're not using the remote control and front panel controls on the TV, use this mode. When main power is on/off, remote control lock is released. 1 4. Treble (Command: k r) To adjust treble. You can also adjust treble in the AUDIO menu. Transmission [k] [r] [ ] [Set lD] [ ] [Data] [Cr] Data Min: 00 - Max: 64 (*transmit by Hexadecimal code) *Refer to 'Real data mapping'. Acknowledgement [r] [] [Set ID] [] [OK/NG] [Data] [x] 1 S. Bass (Command: k s) To adjust bass. You can also adjust bass in the AUDIO menu. TransmissiOn [k] [s][] [set ID][] [Data] [Cr] Data Min: 00 - Max: 64 (*transmit by Hexadecimal code) *Refer to 'Real data mapping'. ACknowledgemen_ [s] [ ][Set ID] [ ] [OK/NG] [Data] [x] 16. Balance (Command: k t) To adjust balance. You can also adjust balance in the AUDIO menu. TransmissiOn[k] [t][] [Set ID][] [Data] [cr] Data Min: 00 - Max: 64 (*transmit by Hexadecimal code) *Refer to 'Real data mapping'. Acknowledgement [t][] [Set ID] [] [OK/NG] [Data] [x] 1 7. Color Temperature (Command: k u) To adjust color temperature. You can also adjust color temperature in the PICTURE menu. TransmisSion [k] [u] [] [set ID] [] [Data] [Cr] Data 00: Medium 01: Cool 02: Warm Acknowledgement[u][ ][set ID][ ][OK/NG] [Data] [x] 18. ISM Method (Command: j p) To avoid having a fixed image remain on screen. TransmisSion [j ][p][ ] [Set ID][] [Data] [Cr] Data 02: Orbiter 04: White Wash 08: Normal 20: Color Wash Acknowledgement[pill [set ID] [ ] [OKSNG] [Data] [x] 1 9. Low Power(Power/Energy Saving) (Command: j q) To reduce the power consumption of the TV. TransmissiOn [j ][q][ ][Set ID][] [Data] [Cr] Data 00: Power/Energy Saving off 01 : Power/Energy Saving: Minimum 02: Power/Energy Saving: Medium 03: Power/Energy Saving: Maximum 10: Intelligent Sensor: Low (For 60PSll ) 11: Intelligent Sensor: Middle (For 60PSll ) 12: Intelligent Sensor: High (For 60PSll ) ACknowledgement [q][] [set ID][ ] [OKiNG] [Data] [x] 20. Auto Configuration (Command: j u) To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode. Transmission[j ] [u] [] [Set ID] [] [Data] [Cr] Data 1 : To set ACknowledgement[u] [ ] [Set ID] [ ] [OK/NG] [Data] [x] 21. Channel Tuning (Command: m a) To tune channel to following physical/major/minor number. TransmisSion[m] [a][] [Set ID] [ ] [Data00] [ ] [Data0! ] [ ] [Data02] [ ] [Data03] [ ] [Data04] [ ] [Data05] [Cr] Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel to the Major number, the Physical number is not required when sending a command. Data 00: Physical Channel Number NTSC air: 02-45, NTSC cable: 01,0E-7D ATSC air: 01-45, ATSC cable: 01-87 Data 01 & 02: Major Channel Number Data 01 : High byte Data 02: Low byte Two bytes are available for the Major and Minor, normally only the second byte is used. Data 03 & 04: Minor Channel Number Not needed for NTSC. Z X 111