LG S3RFBN Owners Manual - Page 18

Installing The Anti-tip, Device, Assembling The Drip Tray, Installing Cap Covers, Installing Hinge

Get LG S3RFBN PDF manuals and user guides View all LG S3RFBN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

18 INSTALLATION 3 Place the adhesive side of the non-skid pad on the floor. This side up Adhesive side B Remove backing 4 Recheck the Styler's levelness. Push or rock the edges of the appliance gently to make sure that the Styler does not rock. If the Styler rocks, level the appliance again. • The pads may leave a sticky residue when they are removed. The residue can be removed with alcohol. ASSEMBLING the DRIP Tray Before using the Styler, insert the drip tray onto the bottom of the cabinet. 1 Hold the tray so the arrow and letter on the front of the tray face up. 2 Insert one side of the tray first, then the other. Push the tray until it slides completely in. 3 To detach, pull one side out then the other. If the tray collects water, detach it and empty the water. After emptying it, re-assemble the tray. installing the anti-tip device • Appliances can tip, resulting in damage or injuries. Do not operate the unit without the anti-tip device in place and engaged. If an anti-tip device is not properly installed, the appliance could be unexpectedly tipped by a child or adult standing, sitting, leaning, or placing excessive weight on an open door or the interior parts. • Install the anti-tip device packed with the Styler to reduce the risk of tipping. Refer to the instructions provided with the antitip kit for proper anti-tip device installation. • Check that the anti-tip device is properly installed. With the appliance in its final location, make sure that the slide adjuster on the cord is adjusted until there is about one inch of slack in the cord. • The use of the anti-tip device does not preclude tipping of the appliance when it is not properly installed. • Do not operate the Styler without installing the drip tray. Doing so could lead to water damage caused by leaking. INSTALLING CAP COVERS 1 Line up the nubs on the cap cover with the holes in the top corner of the cabinet. 2 Snap the cap cover into place. Repeat with the remaining cap cover on the other corner. INSTALLING HINGE COVERS 1 Open the Styler door. 2 Snap the hinge cover onto the lower hinge assembly with the bent edge on the far side from the hinge. 3 Repeat with the remaining hinge cover on the upper hinge assembly. MFL66101237_EN_FR_SP.indd 18 17. 4. 4. 오후 4:55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
18
INSTALLATION
3
Place the adhesive side of the non-skid
pad on the floor.
4 Recheck the Styler's levelness.
Push or rock the edges of the appliance gently
to make sure that the Styler does not rock. If
the Styler rocks, level the appliance again.
•
The pads may leave a sticky residue when
they are removed. The residue can be
removed with alcohol.
INSTALLING THE ANTI-TIP
DEVICE
•
Appliances can tip, resulting in damage or
injuries. Do not operate the unit without the
anti-tip device in place and engaged.
If an anti-tip device is not properly installed,
the appliance could be unexpectedly tipped
by a child or adult standing, sitting, leaning, or
placing excessive weight on an open door or
the interior parts.
•
Install the anti-tip device packed with the
Styler to reduce the risk of tipping.
Refer to the instructions provided with the anti-
tip kit for proper anti-tip device installation.
•
Check that the anti-tip device is properly
installed.
With the appliance in its final location, make
sure that the slide adjuster on the cord is
adjusted until there is about one inch of slack
in the cord.
•
The use of the anti-tip device does not
preclude tipping of the appliance when it is
not properly installed.
ASSEMBLING THE DRIP TRAY
Before using the Styler, insert the drip tray onto
the bottom of the cabinet.
1
Hold the tray so the arrow and letter on
the front of the tray face up.
2
Insert one side of the tray first, then
the other. Push the tray until it slides
completely in.
3
To detach, pull one side out then the other.
If the tray collects water, detach it and empty
the water. After emptying it, re-assemble the
tray.
•
Do not operate the Styler without
installing the drip tray.
Doing so could lead
to water damage caused by leaking.
INSTALLING CAP COVERS
1
Line up the nubs on the cap
cover with the holes in the top
corner of the cabinet.
2
Snap the cap cover into place.
Repeat with the remaining cap
cover on the other corner.
INSTALLING HINGE COVERS
1
Open the Styler door.
2
Snap the hinge cover onto the lower hinge
assembly with the bent edge on the far
side from the hinge.
3
Repeat with the remaining hinge cover on
the upper hinge assembly.
Remove
backing
This side up
Adhesive
side
B
MFL66101237_EN_FR_SP.indd
18
17. 4. 4.
오후 4:55