Lenovo ThinkCentre Edge 91 (English) User Guide - Page 66

Replacing the system fan assembly

Page 66 highlights

What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to "Completing the parts replacement" on page 57. Replacing the system fan assembly Attention: Do not open your computer or attempt any repair before reading and understanding the "Important safety information" on page v. This section provides instructions on how to replace the system fan assembly. To replace the system fan assembly, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See "Removing the computer cover" on page 30. 3. Remove the front bezel. See "Removing and reinstalling the front bezel" on page 30. 4. Pivot the drive bay assembly upward to gain access to the system fan assembly. See "Accessing the system board components and drives" on page 32. 5. Remove the hard disk drive for easier access to the system fan assembly. See "Replacing the hard disk drive" on page 38. 6. Remove the heat sink fan duct. See "Replacing the heat sink and fan assembly" on page 48. 7. Note the cable routing and disconnect the system fan assembly cable from the power fan connector on the system board. See "Locating parts on the system board" on page 12. 8. The system fan assembly is attached to the chassis by four rubber mounts. Remove the system fan assembly by cutting the four rubber mounts 1 and lifting the system fan assembly out of the chassis. Note: The new system fan assembly will have four new rubber mounts attached. Figure 40. Removing the system fan assembly 54 ThinkCentre Edge User Guide 56 78 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132

What to do next:
To work with another piece of hardware, go to the appropriate section.
To complete the replacement, go to “Completing the parts replacement” on page 57.
Replacing the system fan assembly
Attention:
Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
on page v.
This section provides instructions on how to replace the system fan assembly.
To replace the system fan assembly, do the following:
1. Turn off the computer and disconnect all power cords from electrical outlets.
2. Remove the computer cover. See “Removing the computer cover” on page 30.
3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 30.
4. Pivot the drive bay assembly upward to gain access to the system fan assembly. See “Accessing the
system board components and drives” on page 32.
5. Remove the hard disk drive for easier access to the system fan assembly. See “Replacing the hard
disk drive” on page 38.
6. Remove the heat sink fan duct. See “Replacing the heat sink and fan assembly” on page 48.
7. Note the cable routing and disconnect the system fan assembly cable from the power fan connector on
the system board. See “Locating parts on the system board” on page 12.
8. The system fan assembly is attached to the chassis by four rubber mounts. Remove the system fan
assembly by cutting the four rubber mounts
1
and lifting the system fan assembly out of the chassis.
Note:
The new system fan assembly will have four new rubber mounts attached.
Figure 40. Removing the system fan assembly
54
ThinkCentre Edge User Guide