Home » Linksys Manuals » Repeaters & Transceivers » Linksys WRE54G » Manual Viewer

Linksys WRE54G Cisco WAP54GP Wireless-G Exterior Access Point User Guide - Page 20

Ground the Access Point, Attach the Mounting Plate - support

UPC - 745883559046

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Wireless-G Exterior Access Point 6. Make sure that you properly ground the Access Point. 7. Line up the Access Point's wall-mount slots with the two screws on the wall. Then, slide the Access Point down so that the screws fit snugly in the slots. 8. Attach a screw (not included) in each of the two holes on the top of the mounting plate so that the Access Point is securely mounted to the wall. 9. Connect the other end of the Ethernet network cable to a switch, router, or other device that supports Power over Ethernet. The Access Point will then be connected to your wired network. Now that the hardware installation is complete, proceed to "Chapter 5: Setting Up the Wireless-G Exterior Access Point," for directions on how to configure the Access Point. Figure 4-2: Attach the Mounting Plate Chapter 4: Connecting the Wireless-G Exterior Access Point Hardware Installation Figure 4-3: Ground the Access Point 13

Section	Page
Appendix A: Troubleshooting 43	4
Appendix B: Wireless Security 47	4
Appendix C: Upgrading Firmware 50	4
Appendix D: Windows Help 51	4
Appendix E: Glossary 52	4
Appendix F: Specifications 57	4
Appendix G: Warranty Information 59	4
Appendix H: Regulatory Information 60	4
Appendix I: Contact Information 66	4
List of Figures	5
Figure 2-1: Example of a Simple Wireless Network 5	5
Figure 3-1: Front Panel 6	5
Figure 3-2: Bottom Panel 7	5
Figure 3-3: Top Panel 7	5
Figure 3-4: Back Panel 8	5
Figure 3-5: Internal Antenna Pattern (Horizontal Plane) 9	5
Figure 3-6: Radio Coverage of the Access Point to Client Devices 10	5
Figure 3-7: Access Point to Access Point (bridging) Radio Coverage 11	5
Figure 4-1: Mark the Locations of the Two Wall-Mount Slots 12	5
Figure 4-2: Attach the Mounting Plate 12	5
Figure 4-3: Ground the Access Point 13	5
Figure 4-4: Attach the Access Point to the Wall 13	5
Figure 5-1: Login Screen 14	5
Figure 6-1: Setup - Static IP Address 17	5
Figure 6-2: Setup - Automatic Configuration - DHCP 18	5
Figure 6-3: Setup - Time 18	5
Figure 6-4: Wireless - Basic Wireless Settings 19	5
Figure 6-5: Wireless - Wireless Security (Disabled) 21	5
Figure 6-6: Wireless - Wireless Security (WPA-Personal) 21	5
Figure 6-7: Wireless - Wireless Security (WPA2-Personal) 22	5
Figure 6-8: Wireless - Wireless Security (WPA2-Personal Mixed) 22	5
Figure 6-9: Wireless - Wireless Security (WPA-Enterprise) 23	5
Figure 6-10: Wireless - Wireless Security (WPA2-Enterprise) 23	5
Figure 6-11: Wireless - Wireless Security (WPA2 - Enterprise Mixed) 24	5
Figure 6-12: Wireless Security - RADIUS 25	5
Figure 6-13: Wireless Settings - WEP 25	5
Figure 6-14: Wireless - Wireless Connection Control 26	5
Figure 6-1: Select MAC Address from Client Association Table 26	5
Figure 6-15: Wireless - Advanced Wireless 27	6
Figure 6-16: AP Mode 29	6
Figure 6-17: Wireless Repeater 30	6
Figure 6-18: Site Survey 31	6
Figure 6-19: Administration - Management 32	6
Figure 6-20: The Administration - Log 34	6
Figure 6-21: Administration - Factory Default 36	6
Figure 6-22: Administration - Firmware Upgrade 36	6
Figure 6-23: Administration - Reboot 37	6
Figure 6-24: Administration - Config Management 38	6
Figure 6-25: Status - Local Network 39	6
Figure 6-26: Status - Wireless 40	6
Figure 6-27: Status - System Performance 41	6
Figure C-1: Firmware Upgrade 50	6
Chapter 1: Introduction	7
Welcome	7
What’s in this User Guide?	8
Chapter 2: Planning Your Wireless Network	10
Network Topology	10
Roaming	10
Network Layout	10
Example of a Simple Wireless Network	11
Chapter 3: Getting to Know the Wireless-G Exterior Access Point	13
The LEDs	13
The Ports	14
The Reset Button and Ground	15
The Antenna Pattern	16
Chapter 4: Connecting the Wireless-G Exterior Access Point	19
Overview	19
Hardware Installation	19
Chapter 5: Setting Up the Wireless-G Exterior Access Point	21
Overview	21
Accessing the Utility	21
Navigating the Utility	22
Chapter 6: Configuring the Wireless-G Exterior Access Point	24
The Setup Tab	24
The Setup - Time Tab	25
The Wireless - Basic Wireless Settings Tab	26
The Wireless - Wireless Security Tab	28
The Wireless - Wireless Connection Control Tab	33
The Wireless - Advanced Wireless Settings Tab	34
The AP Mode Tab	36
The Administration - Management Tab	39
The Administration - Log Tab	41
The Administration - Factory Default Tab	43
The Administration - Firmware Upgrade Tab	43
The Administration - Reboot Tab	44
The Administration - Config Management Tab	45
The Status - Local Network Tab	46
The Status - Wireless Tab	47
The Status - System Performance Tab	48
Appendix A: Troubleshooting	50
Frequently Asked Questions	50
Appendix B: Wireless Security	56
Security Precautions	56
Security Threats Facing Wireless Networks	56
Appendix C: Upgrading Firmware	59
Appendix D: Windows Help	60
Appendix E: Glossary	61
Appendix F: Specifications	66
Appendix G: Warranty Information	68
Appendix H: Regulatory Information	70

Match case Limit results 1 per page

Chapter 4: Connecting the Wireless-G Exterior Access Point

Hardware Installation

Wireless-G Exterior Access Point

Make sure that you properly ground the Access Point.

Line up the Access Point’s wall-mount slots with the two screws on the wall. Then, slide the Access

Point down so that the screws fit snugly in the slots.

Attach a screw (not included) in each of the two holes on the top of the mounting plate so that the Access

Point is securely mounted to the wall.

Connect the other end of the Ethernet network cable to a switch, router, or other device that supports

Power over Ethernet. The Access Point will then be connected to your wired network.

Now that the hardware installation is complete, proceed to "Chapter 5: Setting Up the Wireless-G Exterior

Access Point," for directions on how to configure the Access Point.

Figure 4-3: Ground the Access Point

Figure 4-2: Attach the Mounting Plate