Marantz SR4400 User Guide - Page 10
Operation Of Remote Control
View all Marantz SR4400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
ENGLISH SCANNING THE CODE TABLE RESETTING THE ALL CODE OSD MENU OSD MENU 2. POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX TV VOL. SLEEP AMP MUTE MAIN VOL. 2. 6. 3. OK SETUP/ T.TONE S-DIRECT AUTO 1 NIGHT CSII 4 DISPLAY M-CH ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES DSP 5 6 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP OSD MENU BASS TREBLE TUNE/SEARCH 1. Switch on the appliance which should be controlled. 2. Press and hold down the function button for appliance which should be controlled and press SETUP until the indicator blinking twice. 3. Press the code 9 - 9 - 1. The indicator will blink twice. 4. Aim the remote control at the appliance and slowly alternate between pressing POWER and the function button for the appliance. 5. Stop when the appliance turns off. 6. Press SETUP once to lock in the code. POWER OK 1. TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX TV VOL. SLEEP AMP MUTE MAIN VOL. 1. 2. SETUP/ T.TONE S-DIRECT AUTO 1 NIGHT CSII 4 DISPLAY M-CH ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES DSP 5 6 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP OSD MENU BASS TREBLE TUNE/SEARCH 1. Press and hold down the any function button and press SETUP until the indicator blinking twice. 2. Press the code 9 - 8 - 1. The indicator will blink twice. Then, RC5400SR will return to the factory preset code. Note: After this procedure, the selected function button is set initial code and other function buttons are set initial code too. CHECKING THE CODE POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX TV VOL. SLEEP AMP MUTE MAIN VOL. 1. 3. 4. 2. OK SETUP/ T.TONE S-DIRECT AUTO 1 NIGHT CSII 4 DISPLAY M-CH ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES DSP 5 6 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH OSD MENU MODE DISP./RDS F.DIRECT 1. Press and hold down the function button for appliance which should be controlled and press SETUP until the indicator blinking twice. 2. Press the code 9 - 9 - 0. The indicator will blink twice. 3. To view the code for first digit, press 1 once. Wait 3 seconds, count the indicator blinks (e.g. 3 blinks = 3) and write down the number. Note: If a code digit is "0", the indicator will not blink. 4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Once you have found and the codes for your various appliances, you may want to write them down here. TV VCR DSS DVD CD TAPE CDR MD OPERATION OF REMOTE CONTROL UNIT REMOTE CONTROL The distance between the transmitter of the remote control unit and the IR SENSOR of the SR4400 should be less than about 5 meters. If the transmitter is pointed to a direction other than the IR SENSOR or if there is an obstacle between them, remote control may not be possible. Remote-controllable range SR4400 Approx. 5 m 60° Remote control unit (RC5400SR) LOADING BATTERIES The life of the batteries used with the remote control unit is about 4 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak. 1. Remove the back cover. 2. Insert the new batteries (AAA type) with correct and polarity. 3. Close until it clicks. 8