Marantz SR4400 User Guide - Page 28

ENGLISH 2. AV SURROUND RECEIVER SR4400 SURROUND STANDBY POWER ON/STANDBY PHONES CLEAR MEMORY 2. A/D HT-EQ 6.1 CH-IN TV DVD VCR1 SETUP/ T.TONE S-DIRECT AUTO 1 NIGHT CSII 4 DISPLAY M-CH ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES DSP 5 6 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH MODE DISP./RDS F.DIRECT /A /ANT /B /VCR ATT PTY 1. Select a desired Video source to decide the routed video signal to the Monitor Outputs . 2. Press the 6.1 CH-IN button on the front panel or on the remote to switch the 6.1 channel input. 3. If necessary to adjust the output level of each channel, use "6.1 Ch. INPUT LEVEL" in SETUP menu system as desired. Adjust the speaker output levels so that you can hear the same sound level from each speaker at the listening position. For the front left, front right, center, surround left, surround right and surround back speakers, the output levels can be adjusted between -10 to +10 dB. The subwoofer can be adjusted between -15 and +10 dB. These adjusting result will be stored to 6.1 Ch. INPUT condition. (see to page 20) 4. Adjust the main volume with the MAIN VOLUME knob or the VOL buttons on the remote. To cancel the 6.1 Ch. INPUT setting, press the 6.1 CH-IN button on the front panel or on the remote. Notes: • When the 6.1 Ch. Input is in use, you may not select a surround mode, as the external decoder determines processing. • In addition, there is no signal at the record outputs when the 6.1 Ch. Input is in use. 26 BASIC OPERATION (TUNER) LISTENING TO THE TUNER Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country's standard is 9 kHz step, Press TUNER button on the remote more than 6 seconds. Scan step will change. Note: • Preset memory for the tuner will clear by changing this setup. AUTO TUNING 3. 2. 1. 1. V CLEAR MEMORY TUNING/PRESET F/P MODE HT-EQ S-DIRECT DISPLAY MUTE TV DVD VCR1 DSS/VCR2 CDR/MD TAPE CD TUNER DOWN 2. TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX TV VOL. SLEEP AMP MUTE MAIN VOL. CLEAR MEMO A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH MODE DISP./RDS F.DIRECT +/A /ANT -/B /VCR ATT. PTY MANUAL TUNING 3. 2. 1. 1. VOL CLEAR MEMORY TUNING/PRESET F/P MODE HT-EQ S-DIRECT DISPLAY MUTE TV DVD VCR1 DSS/VCR2 CDR/MD TAPE CD TUNER DOWN 2. TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX TV VOL. SLEEP AMP MUTE MAIN VOL. CLEAR MEMO A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH MODE DISP./RDS F.DIRECT +/A /ANT -/B /VCR ATT. PTY (USING THE SR4400) 1. To select tuner and desired band (FM or AM), press the TUNER button on the front panel 2. Press the F/P(Frequency/Preset) button on front panel to appears frequency on the display. 3. Press the TUNING or button. (Using the remote control unit) 1. To select tuner and desired band (FM or AM), press TUNER button twice within in two seconds on the remote. 2. Press 5 or 6 on the remote to tune in the desired station. (USING THE SR4400) 1. To select tuner and desired band (FM or AM), press the TUNER button on the front panel. 2. Press the F/P(Frequency/Preset) button on the front panel to appears frequency on the display. 3. Press the TUNING or button on the front panel for more than 1 second to start the Auto tuning function. 4. Automatic searching begins then stops when a station is tuned in. (Using the remote control unit) 1. To select tuner and desired band (FM or AM), press the TUNER button twice within in two seconds on the remote. 2. Press 5 or 6 more than 1 second on the remote. 3. Automatic searching begins then stops when a station is tuned in. DIRECT FREQUENCY CALL 1. 1. 2. 3. 4. POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD 3. S-DIRECT NIGHT DISPLAY CLEAR AUTO 1 CSII 4 M-CH ST 7 MEMO DTS 23 EX/ES DSP 56 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH AUX TV VOL. SLEEP AMP MUTE VOL. 2. MODE DISP./RDS F.DIRECT +/A /ANT -/B /VCR ATT. PTY OSD MENU DISC/DECK SYSTEM REMOTE CONTROLLER To select tuner and desired band (FM or AM), press the TUNER on the remote. Press the F.DIRECT button on the remote, display will show "FREQ - - - ". Input your desired station's frequency with numeric buttons on the remote. The desired station will automatically be tuned. If tuning does not stop at the desired station, use to the "Manual tuning" operation. (FM) TUNING MODE (AUTO STEREO OR MONO) VOLUME DOWN UP ET F/P MODE DISPLAY MUTE CDR/MD TAPE CD TUNER MODE DISP./RDS F.DIRECT +/A /ANT -/B /VCR ATT. PTY DISC/DECK SYSTEM REMOTE CONTROLLER RC5400SR When in the auto stereo mode, AUTO indicator keeps to light on the display. The "ST" indicator lights on when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the "TUNED" and "ST" indicators turn off. If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the MODE button on the front panel or on the remote. "AUTO" indicators turn off ,FM stereo broadcasts are received in monaural and the "ST" indicator turns off. To return to auto stereo mode, press the MODE button on the front panel or on the remote again. AUTO indicator lights on the display. PRESET MEMORY With this unit you can preset up to 30 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired. AUTO PRESET MEMORY This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory. 5. 2. 2.4. 3. 2) 1. 3.1) AV SURROUND RECEIVER SR4400 SURROUND VOLUME DOWN UP CLEAR MEMORY TUNING/PRESET F/P MODE STANDBY POWER ON/STANDBY PHONES A/D HT-EQ S-DIRECT DISPLAY MUTE 6.1 CH-IN TV DVD VCR1 DSS/VCR2 CDR/MD TAPE CD TUNER 1. To select FM , press the TUNER button on the front panel. 2. While pressing the MEMORY button, press the TUNING button to up.