Marantz SR4400 User Guide - Page 9
SETUP / T.TONE button - stereo receiver
View all Marantz SR4400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
ENGLISH . Numeric buttons 1 to 9 (A, B, C ... Z, -) / Surround mode buttons Numeric buttons These buttons are used to enter figures in the selection of a tuner preset station and station name preset or to set select a CD track number, etc. The functions of these buttons are dependent on the function button selected. Surround mode buttons (when AMP mode is selected) These buttons are used to select the surround mode. Note: • The surround mode is set to 6-Stereo mode by pressing M-CH ST button. ⁄0 P.SCAN (preset scan) button (when TUNER mode is selected) This button is used to start preset scan when SR4400 is selected TUNER mode. ⁄1 0 / A/D button 0 button This button is used to enter the number "0" A/D button (when AMP mode is selected) This is used to switch between the analog and digital inputs. ⁄2 CONTROL buttons These buttons are used when operating the CD player, TAPE deck, etc. The function of these buttons are dependent on the function button selected. For the controllable functions of each input function, please refer to contrable function table on the page 9. ⁄3 ATT (attenuator) button When the input signal is too high and the voice distorts even by throttling the SR4400 VOLUME control, turn on this function. "ATT" is indicated when this function is activated. The input level is reduced. Attenuator is invalid for use with the output signal of "REC OUT". Note: • This function is unavailable during the digital input is selected. ⁄4 TREBLE UP ( ) /DOWN ( ) buttons These buttons are used to adjust the tone control of high frequency sound for left and right speaker. ⁄5 BASS UP ( ) /DOWN ( ) buttons These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker. ⁄6 MEMO button Memory enable button for various preset functions. ⁄7 CLEAR button This button is used to cancel for certain memory or programming operations. ⁄8 DISPLAY button When this button is pressed once, the display is dimmed. When this button is pressed twice, the display is turned off and the "DISPLAY OFF" indicator lights up. Press this button again to turn on the display again. ⁄9 NIGHT button Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only for the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back. When this button is pressed, "NIGHT" indicator lights up. ¤0 S- ( Source) DIRECT button When this button is pressed, the tone control circuit is bypassed as well as Bass Management. ¤1 SETUP / T.TONE button Test tone function is used for adjusting the balance between the volume levels of speaker channels. Press AMP button and press this button to enter the test tone mode. ¤2 OSD button Note: • This button is unavailable for SR4400. ¤3 SLEEP (sleep timer) button This button is used for setting the sleep timer. It can be operated the same way as the button in unit. ¤4 TV VOLUME UP ( ) /DOWN ( ) buttons These buttons increase or decrease TV's volume. PROGRAMMING THE REMOTE CONTROLLER The remote controller RC5400SR must be programmed to use the codes for your appliances of different brands. This is done by keying in a 4digit code or by scanning the codes until the correct one is found. We recommend to using the 4-digit code. This mode is faster and more reliable. The code scanning method should be used only if you cannot find the code for one of your appliances. The codes are listed at the end of this book. Important: • Use the remote control buttons for programming, not the buttons of the receiver or other appliances. • Some codes may be not match your equipment. In this case, your equipment cannot be controlled with this remote controller. PROGRAMMING WITH THE 4-DIGIT CODE OK 1. 1. 2. 3. POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX TV VOL. SLEEP AMP MUTE MAIN VOL. 1. 2. SETUP/ T.TONE S-DIRECT AUTO 1 NIGHT CSII 4 DISPLAY M-CH ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES DSP 5 6 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH OSD MENU MODE DISP./RDS F.DIRECT +/A /ANT -/B /VCR ATT. PTY Press and hold down the function button for the appliance which should be controlled and press SETUP until the indicator blinks twice. Press the 4-digit code for appliance (code table at the end of this book) When the procedure is successful, the indicator will blink twice. Note: • If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again. 7