Marantz SR4400 User Guide - Page 30

ENGLISH To move back and forth between the characters, press the TUNING / button or press 4 / ¢ buttons on the remote. Note: • Unused columns should be filled by entering blanks. 6. To save name, press the MEMORY button, press MEMO button on the remote for more than 2 seconds. • You can input the alphabetic and numeric characters with the ten keypad of the remote control in the previous step 4 and 5. 7. 8. S-DIRECT NIGHT DISPLAY CLEAR AUTO 1 CSII 4 M-CH ST 7 MEMO DTS 2 3 EX/ES DSP 5 6 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH MODE DISP./RDS F.DIRECT 7. Enter the character using the ten keypad. For example, to enter "A": 1) Press the "1" button. "A" appears on the display column. 2) Every time the 1 button is pressed, the displayed character changes in the order: A → B → C → 1 → A... Pressing buttons other than the "1" button cause different characters to be displayed in a similar way, so that other alphanumeric characters can be entered. To enter a blank or space, press the "9" button. 8. When the desired character is displayed, press the MEMO button to confirm the entry in this column and move to the next column. After having filled all of the 8 columns, press the MEMO button, for more than 1 second to confirm the entry. TROUBLESHOOTING In case of trouble, check the following before calling for service: 1. Are the connections made properly ? 2. Are you operating the unit properly following user's guide ? 3. Are the power amplifiers and speaker working properly ? If the unit does not operate properly, check items shown in the following table. If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz distributor or the Marantz Service Center in your country. SYMPTOM CAUSE REMEDY SR4400 cannot be turned up. The power plug is not connected. Connect the power plug to the outlet. No sound and picture are Mute is on. Cancel mute using the remote control unit. output even when power is on. The input cable is not connected See the connection diagram and connect the correctly. cables correctly. The master volume control is turned all Adjust the master volume. the way down. The function selector position is wrong. Select correct position. Speaker does not outputting The headphones are connected to the Disconnect the headphones. (Speakers will not any sound. headphone jack. output sound when headphones are connected.) Sound and pictures from other Input cable connected incorrectly. than equipment selected with the function selector. Connect the cable correctly by referring to the connection diagram. Sound from the wrong channel Speaker cable connected incorrectly. Connect the cable correctly by referring to the is output from the speaker. connection diagram. No sound is output from the The center speaker cable connection is Connect the cable correctly. center speaker. incomplete. STEREO has been selected for When STEREO is selected for Surround mode, no Surround mode. sound will be output from the center speaker. Set another Surround mode. Center = NONE has been selected in Make the correct setting. SETUP mode. No sound is output from the T h e s u r r o u n d s p e a k e r c a b l e Connect the cable correctly. surround speakers. connection is incomplete. STEREO has been selected for When STEREO has been selected for Surround Surround mode. mode, no sound will be output from the surround speaker. Set another Surround mode. Surround = NONE has been selected in Make the correct setting. SETUP mode. No sound is output from the The surround back speaker cable Connect the cable correctly. surround back connection is incomplete. Surround mode is not EX/ES mode. Set surround mode EX/ES. Surround back = NONE has been Make the correct setting. selected in SPEAKERS SIZE SETUP. Can not select EX/ES mode. Surround back = NONE has been Make the correct setting. selected in SPEAKERS SIZE SETUP. Input signal is incompatible. Use 5.1channel source. Can not select Pro Logic II Input signal is incompatible. mode. Use 2 channel Dolby Digital input signal, PCM input signal or analog input signal. Can not select Neo:6 mode. Input signal is incompatible. Use PCM input signal or analog input signal. 28