Marantz SR4400 User Guide - Page 8

ENGLISH n Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. m Preamp Outputs (L, R, SL, SR, SB, C) Jacks for L (front left), R (front right), C (Center), SL (surround left), SR (surround right) and SB (surround back). Use these jacks for connection to some external power amplifiers. , 6.1 CHANNEL INPUT By connecting a DVD Audio player, SACD multi channel player, or other component that has a multi channel port, you can playback the audio with 5.1 channel or 6.1 channel output. . Speaker outputs terminals Six terminals are provided for the front left, front right, front center, surround left, surround right and surround back speakers. ⁄0 REMOTE CONT. IN/OUT terminals Connect to a Marantz component equipped with remote control (RC-5) terminals. ⁄1 DIGITAL INPUT (Dig.1 - 4) / OUTPUT (coaxial, optical) These are the digital audio inputs and outputs. There are 2 digital inputs with coaxial jacks, 2 with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component. For digital output, there is 1 coaxial output and 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, DAT decks, or other similar components. ⁄2 Power cable Connect to AC power outlet. SR4400 can be powered by 120 V AC only. Caution: • In order to avoid potential turn-off thumps, anything plugged in here should be powered up before the SR4400 is turned on. ⁄3 AC OUTLETS Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided. The one marked SWITCHED provides power only when the SR4400 is turned on and is useful for components which you use every time you play your system. The one marked UNSWITCHED is always live as long as the SR4400 is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with its own power switch. Caution: • In order to avoid potential turn-off thumps, anything plugged in here should be powered up before the SR4400 is turned on. • The capacity of these AC outlets are 100W. Do not connect devices that consume electricity more than the capacity to these AC outlets. If total power consumption of connected devices exceeds the capacity, protection circuit shuts down the power supply. REMOTE CONTROL OPERATION FUNCTION AND OPERATION The provided remote control unit is a universal remote controller. The POWER button, numeric buttons and control buttons are used in common across different input source components. The input source controlled with the remote control unit changes when one of the input selector buttons is pressed. ¤4 ¤3 ¤2 ¤1 ¤0 ⁄9 ⁄8 ⁄7 ⁄6 ⁄5 ⁄4 POWER TV VCR1 DSS/VCR2 DVD TUNER CD TAPE CDR/MD AUX TV VOL. SLEEP AMP MUTE MAIN VOL. OSD MENU OK SETUP/ T.TONE S-DIRECT AUTO 1 NIGHT CSII 4 DISPLAY M-CH ST 7 CLEAR MEMO MENU OFF DTS 2 3 EX/ES DSP 5 6 STEREO 8 6.1CH IN 9 A/D P.SCAN 0 CHANNEL/SKIP BASS TREBLE TUNE/SEARCH MODE DISP./RDS F.DIRECT +/A /ANT -/B /VCR ATT. PTY DISC/DECK SYSTEM REMOTE CONTROLLER RC5400SR z x c v b n m , . ⁄0 ⁄1 ⁄2 ⁄3 z Transmitting indicator Lights up during a button is pressed and an infrared signal is sending. x (Main) POWER buttons Press to switch the power of the SR4400 ON or OFF after pressing the AMP button. c Input selector buttons/ FUNCTION SELECTOR buttons (AUDIO/VIDEO INPUT) These buttons are used to select a Audio or Video source component. Press one of these buttons once to change the function of the remote control. Press same button within 2 seconds, the input function of the SR4400 is changed. Note: • CDR/MD button is set CDR function at initial. To switch MD function, press and hold down CDR/ MD button and press 2 button. • To return CDR function, press and hold down CDR/MD button and press 1 button. • AUX button is unavailable for SR4400. v MAIN VOLUME UP ( ) /DOWN ( ) buttons Main volume control of the SR4400. The front, surround, center and subwoofer channel volumes controlled by these buttons simultaneously. b MUTE button Muting button of the SR4400. Press this button decrease the sound temporarily . Press this button again to return to the previous sound. When this button is pressed, "MUTE" indicator lights up. n MENU button This button is used to enter the SETUP MAIN MENU. m Cursor buttons ( , , , , OK) Use these button when operating the SETUP MAIN MENU. See page 15. , MENU OFF button This button is used to exit from the SETUP MAIN MENU. 6