Marantz SR4400 User Guide - Page 13
Connecting Audio Components - amplifier
View all Marantz SR4400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
CONNECTING SPEAKER WIRE 1. Strip away approx. 10 mm of wire insulation. 2. Twist the bared wire ends tight to prevent short circuits. 3. Loosen the knob by turning counterclockwise. 4. Insert the bare part of the wire into the hole in the side of each terminal. 5. Tighten the knob by turning clockwise to secure the wire. 1. 2. 3/8 inch (10 mm) 3. 4. 5. Cautions: • Be sure to use speakers with the specified impedance shown on the rear panel of this unit. • To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. • Do not touch the speaker terminals when the power is on. It may cause electric shocks. • Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit. Note: • Be sure to connect the positive and negative cables for the speaker properly. If they are missconnected, the signal phase will reversed and the signal quality will be corrupted. CONNECTING A SUBWOOFER Use the PRE OUT SUBWOOFER jack to connect a powered subwoofer (power amplifier built in ). If your subwoofer is passive type (power amplifier is not built in), connect a monaural power amplifier to the PRE OUT SUBWOOFER jack and connect the subwoofer to the amplifier. LR ENGLISH CONNECTING AUDIO COMPONENTS CD PLAYER TAPE DECK CD RECORDER / MD DECK OUT IN DIGITAL L L OUTPUT R R DIGITAL INPUT LR RL DIGITAL OUT OUTPUT L R LR OUT IN L L R R LR LR RL LR LR TV DVD VCR1 DSS / VCR2 MONITOR The output audio signal from the TAPE OUT jack and the CD-R/MD OUT jack is the sound source currently selected. Caution: • Do not connect this unit and other components to mains power until all connections between components have been completed. Notes: • Insert all plugs and connectors securely. Incomplete connections may make noise. • Be sure to connect the left and right channels properly. Red connectors are for the R(right) channel, and white connectors are for the L(left) channel. • Be sure to connect input and output properly. • Refer to the instructions for each component that is connected with this unit. • Do not bind audio/video connection cables with power cords and speaker cables will result in generating hum or other noise. AM GND FM (75Ω) IN TV L IN DVD IN OUT VIDEO VCR1 IN OUT DSS / VCR2 OUT CDR / MD DVD IN TAPE R IN IN IN OUT IN OUT IN OUT IN OUT AUDIO ANTENNA IN OUT DIG.OUT OPT DIG-1 IN DIG-2 IN DIG.OUT COAX DIG-3 IN DIG-4 IN DIGITAL REMOTE CONTROL SURROUND BACK CENTER R SURROUND L SPEAKER SYSTEMS R FRONT L LR LR VCR1 IN S-VIDEO CD VCR1 OUT MONITOR OUT CENTER SUB WOOFER CENTER CONNECTING DIGITAL AUDIO COMPONENTS L • There are four digital inputs, two coaxial jacks R and two optical jacks, on the rear panel. You can IN FRONT SURROUND SURR. BACK SUB WOOFER SURR. BACK SURROUND FRONT 6.1CH INPUT use PRE OUT these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components. SWITCHED 100W MAX AC OUTLET • There are one digital output with coaxial jack and one with optical jack on the rear panel. These jacks can be connected to CD recorder, MD deck. • Setup the digital audio format of DVD player, or other digital source component. Refer to the instructions for each component to be connected to digital input jacks. • Use fiber optical cables(optical) for DIG-1,2 input jacks. Use 75 ohms coaxial cables(for digital audio or video) for DIG-3,4 input jacks. • You can designate the input for each digital input/output jacks according to your component. See page 16. ANALOG AUDIO DIGITAL AUDIO (COAXIAL) DIGITAL AUDIO (OPTICAL) Notes: • There is no Dolby Digital RF input jack. Please use an external RF demodulator Dolby Digital decoder when connecting the Dolby Digital RF output jack of the video disc player to the digital input jack. • The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly. • Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively. 11