Maytag MSD2554VEY User Instructions - Page 11
Accessories, Water Filter, Certifications - filter number
View all Maytag MSD2554VEY manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice production. • Ice stuck in the delivery chute? Use a plastic utensil to clear the delivery chute. • Has the wrong ice been added to the bin? Use only cubes produced by the current ice maker. • Has the ice melted around the auger (metal spiral} in the ice bin? Empty the ice container. Use warm water to melt the ice if necessary. The dispenser water is not cool enough NOTE: Water from the dispenser is chilled to only 50°F (10°C). • New installation? Allow 24 hours after installation for the water supply to cool completely. • Recently dispensed large amount of water? Allow 24 hours for water supply to cool completely. • Water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water. • Refrigerator connected to a cold water pipe? Make sure the refrigerator is connected to a cold water pipe. See "Water Supply Requirements." Cut Hazard Use a sturdy glass when dispensing ice. Failure to do so can result in cuts. • Is the ice dispenser stalling while dispensing "crushed" ice? Change the ice button from "crushed" to "cubed." If cubed ice dispenses correctly, depress the button for "crushed" ice and begin dispensing again. • Has the dispenser arm been held in too long? Ice will stop dispensing when the arm is held in too long. Wait 3 minutes for dispenser motor to reset before using again. ACCESSORIES To order stainless steel cleaner or replacement filters, call 1-800-688-9900 and ask for the appropriate part number listed below or contact your authorized MAYTAG ®Appliances dealer. In Canada, call 1-800-807-6777. Stainless Steel Cleaner and Polish: Order Part #4396095 Standard Base Filter Cartridge: Order Part #4396841 (T2RFWG2) In Canada, Order Part #4396841B (T2RFWG2) WATER FILTER CERTIFICATIONS The water dispenser will not operate properly Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close completely." Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open. Is the water pressure at least 30 psi (207 kPa)? The water pressure to the home determines the flow from the dispenser. See "Water Supply Requirements." Kink in the home water source line? Straighten the water source line. New installation? Flush and fill the water system. Water filter installed on the refrigerator? The filter may be clogged or incorrectly installed. Is a reverse osmosis water filtration system connected to your cold water supply? See "Water Supply Requirements" in either the Installation Instructions or the Use & Care Guide. Trademark/Pclodel Designation WhMpoot Deluxt, T1WG2 WInrlpool Delltxe'i" l WG2I_ Stale of Caliibrnia Department of Health Services Water Treatment Device Certificate Number 05- 1702 Date Issued: April 6, 2005 Date Revised: September 7, 21105 Re_tacement Element_ T2RFWG2 T_RFWG2 :I'2RFWd2 rl oxaphenc Lead Mercury Water is leaking from the dispenser NOTE: One or two drops of water after dispensing is normal. • Glass not being held under the dispenser long enough? Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever. • New installation? Flush the water system. See "Prepare the Water System" or "Water and Ice Dispensers." • Recently changed water filter? Flush the water system. See "Prepare the Water System" or "Water and Ice Dispensers." RatedServiceCapacity: 200gals Rated Service Flow: 05gpm Conditions of Certification: Do not use wJih water tha_ is miclobiologica/ly af_cr the system unsafi: or of unknown quality, without adequate disinibcIion belbre or 11