NEC LCD4010-BK LCD4010 external control command - Page 13

Monitor ID: Indicates a replying Monitor ID.

Page 13 highlights

Header SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get a value. Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller 'E' (45h): Message Type is "Set parameter command" '0'-'A' (30h, 41h): Message length is 10 bytes Message STX (02h): Start of Message '0'-'2' (30h, 32h): Operation code page number is 0 '7'-'8' (37h, 38h): Operation code is 78h (on page 2) '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Select the temperature sensor #1 (01h). 00h: No meaning 01h: Sensor #1 02h: Sensor #2 ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.5 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet Step 2. The monitor replies for confirmation. Header SOH-'0'-'0'-Monitor ID-'F'-'1'-'2' Message STX-'0'-'0'-'0'-'2'-'7'-'8'-'0'-'0'-'0'-'0' -'0'-'2'-'0'-'0'-'0'-'1'-ETX Check code BCC Header SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller Monitor ID: Indicates a replying Monitor ID. Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'F' (46h): Message Type is "Set parameter reply" '1'-'2' (30h, 32h): Message length is 18 bytes Message STX (02h): Start of Message '0'-'0' (30h, 30h): Result code. No error '0'-'2' (30h, 32h): Operation code page number is 0 '7'-'8' (37h, 38h): Operation code is 78h (in the page 2) '0'-'0' (30h, 30h): This operation is "Set parameter" type '0'-'0'-'0'-'2' (30h, 30h, 30h, 32h): Number of temperature sensors 2 (0002h). '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): temperature sensor is #1. ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.5 "Check code" for a BCC calculation. Delimiter CR (0Dh): End of packet Delimiter CR Step 3. The controller requests the monitor to send the temperature from the selected sensor. Header SOH-'0'-Monitor ID-'0'-'C'-'0'-'6' Message Check code STX-'0'-'2'-'7'-'9'-ETX BCC Delimiter CR Header SOH (01h): Start of Header '0' (30h): Reserved (13/37)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37

(13/37)
Header
SOH (01h): Start of Header
'0' (30h): Reserved
Monitor ID: Specify the Monitor ID which you want to get a value.
Ex.) If Monitor ID is '1', specify 'A'.
'0' (30h): Message sender is the controller
'E' (45h): Message Type is "Set parameter command"
'0'-'A' (30h, 41h): Message length is 10 bytes
Message
STX (02h): Start of Message
'0'-'2' (30h, 32h): Operation code page number is 0
'7'-'8' (37h, 38h): Operation code is 78h (on page 2)
'0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Select the temperature sensor #1 (01h).
00h: No meaning
01h: Sensor #1
02h: Sensor #2
ETX (03h): End of Message
Check code
BCC: Block Check Code
Refer to the section 4.5 “Check code” for a BCC calculation.
Delimiter
CR (0Dh): End of packet
Step 2. The monitor replies for confirmation.
Header
SOH (01h): Start of Header
'0' (30h): Reserved
'0' (30h): Message receiver is the controller
Monitor ID: Indicates a replying Monitor ID.
Ex.) When this byte is set to 'A', the replying Monitor ID is '1'.
'F' (46h): Message Type is "Set parameter reply"
'1'-'2' (30h, 32h): Message length is 18 bytes
Message
STX (02h): Start of Message
'0'-'0' (30h, 30h): Result code.
No error
'0'-'2' (30h, 32h): Operation code page number is 0
'7'-'8' (37h, 38h): Operation code is 78h (in the page 2)
'0'-'0' (30h, 30h): This operation is "Set parameter" type
'0'-'0'-'0'-'2' (30h, 30h, 30h, 32h): Number of temperature sensors 2 (0002h).
'0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): temperature sensor is #1.
ETX (03h): End of Message
Check code
BCC: Block Check Code
Refer to the section 4.5 “Check code” for a BCC calculation.
Delimiter
CR (0Dh): End of packet
Step 3. The controller requests the monitor to send the temperature from the selected sensor.
Header
Message
Check code
Delimiter
SOH-'0'-Monitor ID-'0'-'C'-'0'-'6'
STX-'0'-'2'-'7'-'9'-ETX
BCC
CR
Header
SOH (01h): Start of Header
'0' (30h): Reserved
Header
Message
Check
code
Delimiter
SOH-'0'-'0'-Monitor ID-'F'-'1'-'2' STX-'0'-'0'-'0'-'2'-'7'-'8'-'0'-'0'-'0'-'0'
-'0'-'2'-'0'-'0'-'0'-'1'-ETX
BCC
CR